Hydraulic seals factory manufacturer from dmsseals.com: Every other leak path within the mechanical seal is blocked with the use off a gasket, o-ring, wedge (Rubber, PTFE or Flexible Graphite). The other key aspect of a mechanical pump seal is how to maintain the seal. Springs (single or multiple), a metal bellows or just compressed elastomers are used to provide the needed energy to keep pressing the seal faces together. The load the seal faces receive are engineered into the design of the seal. The choice of what is the best depends on the temperature, and nature of what is being sealed (viscosity, abrasiveness, weight (is it a slurry?)). Cartridge Seals are pre-assembled package of mechanical seal components making installation much easier with fewer points for potential mechanical pump seal installation errors to occur. Mechanical seals occasionally require a seal pot to provide a buffer fluid for your double cartridge seals. Seal pots can not only provide a lubricating buffer, but they can also heat or cool the barrier fluid they contain. Read extra details on https://www.dmsseals.com/.
Before examining how mechanical seals function it is important to understand other methods of forming this seal. One such method still widely used is Gland Packing. Gland packing is a braided, rope like material that is packed around the shaft – physically stuffing the gap between the shaft and the pump housing. Gland packing is still commonly used in many applications, however increasingly users are adopting mechanical seals for the following reasons; The friction of the shaft rotating wears away at the packing over time, which leads to increased leakage until the packing is adjusted or re-packed. The friction of the shaft also means that packing also needs to be flushed with large volumes of water in order to keep it cool. Packing needs to press against the shaft in order to reduce leakage – this means that the pump needs more drive power to turn the shaft, wasting energy. Because packing needs to contact the shaft it will eventually wear a groove into it, which can be costly to repair or replace.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
The rod seal is the most important sealing component designed by DMS SEALS in the liquid sealing application. It can effectively prevent the liquid inside the cylinder from leaking to the outside. Moreover, if there is a leakage problem in the rod seal, the performance of the equipment will be degraded. There are even some machine and human safety issues in extreme cases. This type of seal meets the standards of GB/T 15242.1-94 and GB/T 15242.3-94. It is ideal for high and low-speed reciprocating rods and rods in high-pressure system cylinders. Moreover, it can be used in a variety of fluids and high-temperature environments. It is characterized by its high corrosion resistance and its ability to work well in a corrosive media with no oil spots. It has high stability under pressure and harsh conditions. The outstanding advantages of our seals are strong wear resistance, resistance to extrusion, low friction and no stick-slip.
The selection principle of the gasket: according to the working pressure, working temperature, the corrosiveness of the sealing medium and the form of the sealing surface. Temperature influence: In normal temperature and low pressure, use non-metallic soft honey gasket; in medium pressure and high temperature, choose metal and non-metal combination gasket or metal gasket; when temperature and pressure fluctuate greatly, choose good elasticity or self-tightening type Gaskets; in low temperature, corrosive media or vacuum conditions, gaskets with special properties should be considered.
DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. Find extra details at https://www.dmsseals.com/.
DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.
Key points of engineering mechanical seal design: Select a reasonable sealing scheme, focusing on the above requirements. First of all, the dustproof performance must be good. More than 80% of the failures of the hydraulic system are directly or indirectly derived from the stains in the system. Choose the best seals For seals of the same structure, the product quality of each company varies greatly. On the whole, the quality of large foreign seal companies is relatively stable, but the probability of encountering fakes is too high. Sometimes the so-called direct supply is not reliable. In terms of domestic seals, most of them are not very good, but at present, some manufacturers’ products have been chasing or even surpassing imported products, with stable and reliable quality, such as tetrafluoroethylene and rubber seals produced by Damson Sealing.
The spring seal produced by DMS SEALS is perfect for being applied to extremely high-speed, very low-speed equipment with micro piston strokes and other special operating conditions. It can be used with rotary seals and maintains good sealing performance in violent shake and vibration motion environments. At the same time, our seals are extremely adaptable to a wide range of working media. It is resistant to a wide range of chemicals except for soluble alkali metals, high-temperature fluorine and chlorine trifluoride. Therefore, it works well with liquids such as oils and water with high and low temperature.