Author: Amelia Whitehart

TIG welders shop United Kingdom right now: There’s a 100% guarantee that your head won’t fit in any helmet you try the first time you try it. All too often, helmets end up one-size-fits-all in design, which unfortunately means that one size fits no one. An adjustable helmet will have various tension and position adjustments to make sure the helmet fits comfortably and snugly enough to not move around but not so tight that it becomes painful or distracting. It should also be adjustable up and down to adjust your view. Some welding helmets come with inner liners and headgear that can be adjusted more than the built-in adjustments the helmet itself has. The most advanced helmets have completely replaceable webbing that is both elastic and adjustable; these stretch out over time but can be replaced with a newer iteration, so you don’t have to replace an entire helmet because a little bit of strapping wears out. See even more info on fume extractors.

What is the most important safety gear for a welder? The most critical safety gear includes a welding helmet with proper shade, fire-resistant gloves, aprons, and safety boots to protect against sparks, heat, and radiation. How often should welding equipment be inspected? Welding equipment should be inspected before each use to ensure it is in safe working condition, with more thorough maintenance checks scheduled monthly or as per the manufacturer’s guidelines. What are the common signs of inadequate ventilation in a welding area? Common signs include visible fumes, unusual odors, and workers experiencing headaches or dizziness, which indicate poor air quality and insufficient fume extraction. Is certification mandatory for welders? While not always legally mandatory, certification is highly recommended as it verifies a welder’s ability to safely and effectively perform welding tasks according to industry standards.

Temperature control is important in welding. Too hot, and the metals can change properties, melt through and burn away, or end up significantly weaker than the surrounding material. Too low, and the metals won’t melt enough to mix and join. Since molten metal is susceptible to chemical changes much more easily than solid metal, arc welding generally uses some form of shielding gas to protect the weld pool from oxygen and other inclusions. This may be generated through the use of flux that produces the gasses when it melts, or can be pumped in from a gas supply. What is Brazing? Brazing is similar to welding in two ways: it uses higher temperatures (though not as high as welding), and it joins two pieces of metal together with a filler material, filling the gap and providing a strong joint. The biggest difference is how it works. With brazing, the base materials are not melted at all. Instead, the two materials fit together with a minuscule gap between them. This gap is enough space so that capillary action can draw a liquid into that spacing. In this case, the liquid is a molten filler metal.

Resistance or pressure welding uses the application of pressure and current between two metal surfaces to create fusion. Workpieces are placed in contact together at high pressure with a current passing through the contact point. The resistance in the metals generates heat which fuses together the metal surfaces of the workpiece. Resistance spot welding (RSW) uses two electrodes to press together overlapping metals while a welding current is applied through the resistive metals. Heat is generated and the metal surfaces fuse together to create a weld joint in the shape of a button or nugget. Metals are fused using large amounts of energy in a short time span (approx. 10-100 milliseconds) joining the workpieces almost instantaneously. The area around the weld nugget stays unharmed by the excessive heat, thus the heat-affected zone is minimal with spot welding.

How to pick a welder tips: Digital meters factory fitted: Great to have when you purchase and may be required for calibration requirements. To fit them down the line could be expensive. Drive rollers: Metal rollers are the best. Nylon & plastic ones will always wear away quicker. Drive block system: Four roll would always be first choice, but some of the lower amperage machines won’t have them & two roll therefore would be acceptable. Bottle trolley: If you want a stepped voltage machine to be portable, you’ll need one. If you have a full size industrial cylinder check that the running gear & cylinder rack are man enough.

US tool brand DeWalt are known for making the best angle grinders, and the DCG405N is a step above the competition. Cutting the cord once and for all, this is a powerful grinder that makes use of DeWalt’s excellent XR battery system. This Dewalt angle grinder is not just a powerful cordless grinder though. The grip shape is supremely comfortable, and the whole unit weighs just 1 kg without the battery installed. You can lock-off the power switch when you need to get the grinder into awkward spots as well. This brushless angle grinder also features a host of clever safety features. I like the no-volt release to prevent accidental start-ups when a new battery is installed. The electronic brake and clutch are essential for safe operation too. The 18V brushless motor is ideal for battery use. It can make 69 cuts in ½” steel rebar when used with a 5.0 Ah battery. It doesn’t come with any batteries or one of DeWalt’s excellent TSTAK cases though, which is the case with bare power tools.

Although this class of welders is referred to generically as MIG welders, the technical definition is “wire feed”, meaning they use a motor-driven spool to feed wire into the weld puddle. MIG means “Metal-Inert Gas” and refers to a flow of inert gas that shields the metal wire as it is consumed and melts into the puddle. If the machine isn’t able to connect and regulate a flow of inert gas like argon or carbon dioxide, it’s technically not a MIG welder. An example in this review is the Forney Easy Weld 140 FC-i, which doesn’t have gas shielding capability. This is a flux-core wire feed machine. The wire that’s used in these machines has welding flux embedded in the core. When it hits the arc, the metal melts and the flux is released as vapor, providing a shielding gas. This was originally designed as a way to deal with windy conditions defeating the gas shield of a MIG torch. It’s not as clean as true MIG welding but usually, the difference is minor, especially in a home workshop setting. However, with aluminum or stainless steel, the weld won’t be correctly joined without true gas shielding and a quiet setting. Flux core won’t be enough for these projects.

A few advices on welding equipment, MIG and TIG welders, plasma cutters. The welding setup, welder settings, and electrode selection will impact how fast welders can work. Industrial welders invest time in planning the size and shape of their welding areas, how parts are laid out, and how they supply their shielding gas. Testing settings or an electrode on a piece of scrap metal, especially for a beginners, will save time in the long run. Learn more about setting up an efficient shop here. Welding Downhill Increases Welding Speed: While welding downhill is a faster way to weld, it’s not as strong as welding uphill. On most projects it’s not worth sacrificing strength and durability for the sake of welding speed. However, if the metal is thin enough, then welding downhill won’t make the weld weaker and may even be the correct technique for the job. Learn about uphill and downhill welding and see these diagrams of vertical and downhill welding.

This portable weld fume extractor weighs 50 pounds only and features a 16-foot flexible wire. I’ve found the wheels to be extremely useful to move it around anywhere I need. It’s perfect for people who want something efficient but highly portable as well. The S130/G130 is an excellent option for manual welding around the house and store. Adaptable and Durable. The S130/G130 is a highly adaptable and powerful welding fumes extraction system in a small size. This unit can be used at welding school training due to its compact build quality and efficient fume extraction system. The 16-inch hose that it comes with is enough to cover any small to medium area. The machine is made with high-quality steel that makes it sturdy and durable.

The Skil 10 inch drill press is equipped with a 5-speed gearing system which makes it versatile. Thus speed variation can quickly be done for drilling with different bits, bit sizes, and materials. This is a manual belt adjusted for changing speeds. Skil 10 inch drill press is built with quality materials, and one of the best budget mag drill presses in the market available. This low price pick drill press powered with 120 volts. It has a five-speed function like 570, 900, 1390, 2050, 3050 rpm.

The ESAB group is owned by Colfax Corporation. Over 100 years after the company was founded, ESAB serves a global market for welding and cutting equipment. The group is organized in the regions Europe, North America, South America, Asia/Pacific and India. ESAB is represented in almost every country by subsidiaries or agents. Sales and support is established in 80 countries and there are 26 manufacturing plants across four continents. Visit the web site of your nearest ESAB office to find out more. Customers Talk, We Listen – The voice of the customer will always drive the development of our strategic plans and actions. Living this value is done by getting Customer Input and Expectations, at every opportunity, and by differentiating ourselves in How We Deliver to our customers. Innovation Defines Our Future – Individual and organizational creativity will drive breakthrough ideas for technology, products, solutions, and processes. We live this value by providing differentiated customer solutions, creating products and services that improve quality of life and environmental stewardship through Creative Thinking, and by understanding What Innovation Brings.

Our welding tables are to be self-assembled. This is an easy process; full instructions are provided. A wide range of tools are available for use with these tables and they are available as added optional extras in the custom options above. If you require guidance on which tool set would be the most suitable for you please feel free to call our helpful staff. *Please note that current lead times on these welding tables are 3-4 weeks, however if you require the table quicker please alert us and we will do our best to assist with your enquiry*

The Hobart Handler 140 is an excellent choice for beginner welders, which is why it’s probably the most popular welder on the market. This thing is solidly built and is a step above many of the other 140A welders. The arc runs smooth and produces great results. It’s suitable for a range of general repair tasks and projects like trailer frames, autobody repair and anything up to 1/4 inch thick. If you’re just getting into welding, you can’t go wrong with this little machine! What’s better is that it’s an absolute steal at under $500. See the full review here.

It’s also worth looking into how your welder will handle things like short-circuiting. If a short circuit issue occurs while you’re welding, you don’t want a surge of power to ruin your work. Fortunately, there are many welding companies that implement strategies in their devices to eliminate the risks of short circuits. To choose the correct portability, size and weight for your welder, you’ll need to think about what you’ll need the machine for. If you’re going to be carrying it around a lot, then you need something that’s going to be highly portable and lightweight. Just make sure that a reduction in weight doesn’t mean that you end up compromising on power or performance. Discover additional details on this website.

Gasless welding, which is also called “Gasless” or “No-Gas” welding, is the main convenience of contemporary MIG welders. That means they can make welds either with or without gas. It is possible thanks to the use of a special tubular wire filled with a flux and metal powder called a flux-cored wire. In a nutshell, when a flux-cored wire is used, its components generate a shielding gas under a high temperature that is essential for a high-quality joint. The thermal overload protection is also a useful feature that will switch the unit off automatically if the temperature reaches a certain level. Surely, a MIG welder is not something you will carry every minute. Yet, if a machine is lightweight and fitted with wheels, using it will be much more pleasurable. Finally, pay attention to the kit each tool comes with. Some models include a welding shield, coil, attachment for flux-cored welding, hammer, or brush. So, take these features into account when buying a welder.

United Kingdom market choice: LOTOS Technology is a California company that has only been around since 2007. Still, the LOTOS MIG is impactful and high quality enough to make it onto our list. This one is a versatile machine that is a fair price of about $400. And—provided that you have the necessary 240-volt outlet in your home—it can be set up in a matter of minutes. The duty cycle of this welding newcomer is impressive, and it can be utilized by pros and amateurs who have been continually impressed by the bang they’ve gotten for their buck. The LOTOS can weld steel and stainless steel from 18 gauge to ¼ inches and aluminum to 1/8 inch or thicker. Thermal overload protection doesn’t let this machine overheat, and infinitely adjustable heat/amperage as well as wire speed makes using the LOTOS simple. Check out the LOTOS MIG140 for a lower power alternative.

Important Industrial Gas Cylinder Safety Guidelines to Keep in Mind: Acetylene and oxygen are two industrial gases widely used across various industries. The cylinders accommodating these gases are designed with user’s safety in mind. However, that is not enough to ensure optimum safety in an industrial facility. The following factors will help ensure the same: Understand the Cylinder Properly: A personnel should be familiar with the potential risks and hazards associated with compressed gases while handling them. It is important to understand the properties of the gas filled within such as toxicity, flammability limits, and toxicity – Threshold Limit Value (TLV). Also, it is important to understand the hazards posed by gas at low temperature, high pressure or due to the physical state of the gas – non-liquefied or liquefied, etc. A personnel should read the contents of the label on the cylinder. If the label is missing or not easily readable, then the cylinder should not be used. In addition to improving a personnel’s understanding on oxygen cylinder safety or acetylene cylinder safety, he should be administered a proper plant safety training.

Look for ways to create more efficiencies in the welding process. This includes examining such things as wire diameter, wire feed speed, voltage, travel speed, gas type, transfer mode, etc. For instance, if the shop is currently welding with a short arc process and a 75/25 blend of shielding gas, it may be more effective to switch to a different gas and a spray mode of transfer. Or, a change in process may be warranted based on the condition of the part. If there is oxide on the part, it may be easier to change to a process that will overcome contamination problems rather than try to clean each part before welding. Your welding supplier should be up to date on the latest technology and be able to advise you on new processes, machinery and consumables that can optimize welding at the shop. In some cases, it may be better to double bevel a joint to prepare it for welding rather than single bevel it. It is recommended to double bevel any material that is more than 3/4″ in thickness. Just this simple change in procedure can save quite a bit in weld metal. On a 3/4″ thick piece, a double bevel will use 1.45 lbs. per foot of weld metal while a single bevel will use 1.95 lbs. per foot.

Induction heaters supplier UK in 2024: Welding can easily ignite flammable materials due to sparks and hot equipment. It is essential to keep the welding area clear of all flammable materials, including oils, solvents, and combustible debris. Purpose: implementing strict fire safety protocols helps prevent fires, protecting both personnel and facilities. Fire fighting equipment like extinguishers should be readily available, and all staff must know how to use them effectively. Welding equipment should be properly grounded, and all electrical connections must be secure to prevent shocks. Regular inspections of equipment for damaged cords and improper connections are mandatory. Discover additional information on Laser welders.

Brazing requires the use of a flux for three reasons. First, the flux aids in the capillary action required to pull the filler into the joint spacing. Second, it promotes the even spread of the filler metal throughout and over the base material in a process known as wetting. Third, the flux helps remove any oxides and other impurities that would come from the brazing process and weaken the joint. Note: capillary action is a quirk of physics where the interaction of adhesive and cohesive forces draw a liquid along a narrow gap, usually a tube. It’s a somewhat complex concept to explain in terms of pure physics, but fortunately, you don’t need to know the physics to know it works and use it in brazing. You can read more about capillary action here if you’re curious. Brazing is most often found in pipe fitting, particularly in plumbing; most metal pipes in a typical household are fit together using a brazing process.

At the end of the day, the best helmet is the one that matches your needs and fits within your budget. If you weld once a week or less, you don’t need an expensive helmet with all the bells and whistles. On the other hand, if you’re welding all the time, you want something with features that can help keep you safe and operating at peak efficiency. The last thing you need is to damage your eyesight over time or burn your skin from exposure to UV radiation. Every welding operator will have different needs and requirements out of their helmet. If you can, it’s usually a good idea to find a local supplier you can use to try out the fit and feel of various helmets, so you aren’t ordering them sight-unseen from the internet and hoping they work. Once you have some idea of the range of features you need, you can shop more intently for specific helmets and buy the one that matches your requirements.

The Hobart Handler 140 is a bit of a hybrid between pro-level performance and homeowner convenience. The 140-amp rating is enough to weld up to 1/4-inch steel. This machine works both as a flux core welder and as a MIG. The duty cycle is 20 percent at 90 amps. That’s enough power to do most jobs you’ll ever tackle in a home shop setting, but for professionals working on heavy stuff like trailer frames or pipe fencing, it’s just not going to be enough. For other professional work like auto body or welding brackets, mountings and the like, this machine can run off a 4000-watt generator. It’s small enough to carry into a home for HVAC repair and the 110/115/120 input means you could use a small generator or the household receptacle to do the work. The solid aluminum wire drive accommodates either 4 or 8-inch spools and it’s selectable between multiple gauges of wire. The Hobart Handler 140 is backed by a 3-year warranty and its professional features and true MIG capability make it the our Pro Value Pick in this review roundup.

If you’re looking for a reliable cutting disc that can handle a variety of materials, this tool is a great option. This 10-pack of disc grinder cutting wheels is perfect for cutting metal and stainless steel surfaces. With thin metal cutting discs, you can easily get into tight spaces, and they are durable enough to handle even the toughest jobs. Whether you’re a professional contractor or a DIY enthusiast, these disc grinder cutting wheels are sure to come in handy. It’s made of durable aluminum oxide grains that provide an aggressive cutting action and longer service life. Due to the reinforced double fiberglass mesh, this disc meets the MPA en12413 standard. The Panlen Metal&Stainless Steel Cut-Off Disc for Angle Grinder is the perfect accessory for anyone with a 4.5 inch disc grinder. With this size, the cutting discs reach up to 13,000 RPM and 80M/S speeds. You can cut carbon steel, pipe, iron, copper and all other ferrous metals. It is made from tough abrasive materials, this disc can easily take on even the most challenging projects.

One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.

How to pick a welder tips: Digital meters factory fitted: Great to have when you purchase and may be required for calibration requirements. To fit them down the line could be expensive. Drive rollers: Metal rollers are the best. Nylon & plastic ones will always wear away quicker. Drive block system: Four roll would always be first choice, but some of the lower amperage machines won’t have them & two roll therefore would be acceptable. Bottle trolley: If you want a stepped voltage machine to be portable, you’ll need one. If you have a full size industrial cylinder check that the running gear & cylinder rack are man enough.

Angle grinders are formidable tools and need plenty of power to spin cutting or grinding discs at high velocity. Look for corded angle grinders that spin between 11,000-12,000 rpm or cordless angle grinders that spin between 7,500-9,000 rpm. The best angle grinder should be powered by a 700W motor at minimum if corded or, if cordless, an 18V battery that has a capacity of at least 4Ah. The grinding wheel diameter on most angle grinders is usually 115-125 mm, although heavy-duty angle grinders can accommodate grinding tools over twice that size. Noise and vibration levels are important aspects to consider with this type of power tool. Often the best angle grinders are the least noisy with lower vibration levels. This is especially so with cordless versions with brushless motors but they are more expensive, particularly if you include the cost of a battery and charger.

Some tips about welding equipment, MIG and TIG welders, plasma cutters. Welding faster may sound appealing, but aside from practice, there are few shortcuts when creating a strong weld. In fact, unless a situation calls for a fast-moving weld, there’s a good chance that slow and steady is the way to go. An online search for ways to weld faster, will yield either descriptions of the ways automated welding has increased welding speed or press releases from companies who claim their gas or electrode holds the key to improving welding speed. In other words, it can seem like spending a lot of money is the only way to weld faster. However, for those looking for some ways to save time on their welding projects, there are some ways to weld faster for certain projects. While it’s not always a good idea to find a way to weld faster, there are situations when welding faster may produce a better product or a few simple changes can speed up the time on task.

At first glance, it didn’t appear to be a portable fume extractor to me. But, the wheels and the adjustable arm convinced me differently. This machine has a component that’s 10-foot long. And it’s designed to handle two or fewer solid wire coils per month. The machine can generate 750 cubic feet of airflow per minute. It’s a pretty decent amount considering the 0.75 HP motor it comes with. 110V input voltage is required to run the 0.75 HP motor. The horsepower and airflow are enough to clear out welding fumes generated from small projects at your home. The VentBoss S110/G110 comes with a blower wheel that’s reverse-inclined and performs better than you’d expect. It produces 67 dBA sounds which wouldn’t cross the verge of endurance. As a welder, I definitely appreciate the flexibility of this light-duty instrument. I found it quite useful for GMAW, MIG welding, stick welding, and gas metal arc welding.

Nova Voyager DVR magnetic drill is one of the very first smart and most featured drill press. This also plugs and play type drill press with advanced direct-drive motor technology and safety sensors. This drill press recognized as the best versatile and well-featured drill press available in the market. It can handle glass, plastics, metal, and wood for any innovative projects. With no load, it can run 50 rpm to 5500 rpm variable forward speed as well as reverse speed.

The ESAB group is owned by Colfax Corporation. Over 100 years after the company was founded, ESAB serves a global market for welding and cutting equipment. The group is organized in the regions Europe, North America, South America, Asia/Pacific and India. ESAB is represented in almost every country by subsidiaries or agents. Sales and support is established in 80 countries and there are 26 manufacturing plants across four continents. Visit the web site of your nearest ESAB office to find out more. Customers Talk, We Listen – The voice of the customer will always drive the development of our strategic plans and actions. Living this value is done by getting Customer Input and Expectations, at every opportunity, and by differentiating ourselves in How We Deliver to our customers. Innovation Defines Our Future – Individual and organizational creativity will drive breakthrough ideas for technology, products, solutions, and processes. We live this value by providing differentiated customer solutions, creating products and services that improve quality of life and environmental stewardship through Creative Thinking, and by understanding What Innovation Brings.

These welding tables are manufactured to the highest standards in Poland, Europe by GPPH. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. The hole system that these welding benches offer make precise construction a much quicker process when used in conjunction with the optional tool sets. Batch work processing times can be cut in half when you eliminate the measure and exact angle arrangement of individual parts – this makes producing the same item simple and fast.

The Lincoln PowerMIG 210 is the ultimate MIG welder for versatility. It comes with the capability to perform MIG, Stick, TIG and Flux Core welding at both 120v and 240v. This is perfect if you’re looking to buy a MIG welder and are considering buying a TIG or Stick welder as well. Buying a multi-process welder like the PowerMIG 210 can save you a lot of money rather than buying separate machines. Lincoln are the market leaders when it comes to manufacturing quality and the PowerMIG 210 is top of the range to build quality and weld quality. The digital display on the front of the machine lets you easily key in your variables to get you get set up in no time at all with an easy to use user interface. See the full review here.

The people behind Display4top market this particular model as a professional MIG welder and we can’t say that they make a poor case in that regard. For one, its duty cycle is definitely up there. With its 48A rated output, the model is able to work for 6 minutes straight before overheating. It comes equipped with a variable wire speed control trigger, so you’ll be able to efficiently work with different metals. There are two power settings and an Ampere knob, further making the versatility case. More importantly, the model is as durable as they come. The forced air cooling system keeps the temperature at a nice, practical level. On top of that, the welder incorporates a thermal overload protection system that will be able to pick up the former’s slack in case it fails to do its job.

UK market dive: The Ironman is a high-powered welder that is very different from the other welders on this list! Boasting more power, the best duty cycle, and a weight that dwarfs the others, the Ironman is nearly without compare. Obviously, this is not the machine that a budding welder should vie for. It’s super heavy duty and will set the consumer back $2000. It welds from 24 gauge to an amazing ½ inch thickness for steel. The Ironman can handle steel, stainless steel, and aluminum. It is capable of Flux core. The “fan-on-demand” cooling system works as needed, offering up a reduced use of power. There are twelve voltage power settings. The Ironman has infinite adjustment for wire speed.

Important Industrial Gas Cylinder Safety Guidelines to Keep in Mind: Acetylene and oxygen are two industrial gases widely used across various industries. The cylinders accommodating these gases are designed with user’s safety in mind. However, that is not enough to ensure optimum safety in an industrial facility. The following factors will help ensure the same: Understand the Cylinder Properly: A personnel should be familiar with the potential risks and hazards associated with compressed gases while handling them. It is important to understand the properties of the gas filled within such as toxicity, flammability limits, and toxicity – Threshold Limit Value (TLV). Also, it is important to understand the hazards posed by gas at low temperature, high pressure or due to the physical state of the gas – non-liquefied or liquefied, etc. A personnel should read the contents of the label on the cylinder. If the label is missing or not easily readable, then the cylinder should not be used. In addition to improving a personnel’s understanding on oxygen cylinder safety or acetylene cylinder safety, he should be administered a proper plant safety training.

A MIG welder or a metal inert gas welder is a great tool to use when making home DIY projects. With it, you can make a picture frame and a rack to cover your home safe. You can even make your own traditional door knocker if you are not into wireless doorbells. Whether you’re looking for a small MIG welder you can use around the house for basic DIY projects, or you’re looking for a car arc welder that you can take with you on professional jobs, there are various things you’ll need to consider. For instance, man wearing gloves to safely weld metalthe first step is figuring out where you’re going to use your welder. The best welder for home use might not be the same as the ideal machine for your day-to-day business jobs. If you need your arc welder to work effectively in a garage, then you might have to look for an option with a specific range of safety functions to keep you secure as you work. Read additional info on here.

Shielding gas is simultaneously supplied to the weld area to create a protective layer from atmospheric contamination. The simplicity of this welding technique allows it to be one of the preferred choices for industrial welding, manufacturing, construction and for the automotive sector. GMAW has pretty much replaced atomic hydrogen welding (AHW), mainly because of the availability of inexpensive inert gases. Tungsten inert gas welding uses a non-consumable tungsten electrode and an inert shielding gas. In contrast to MIG/MAG welding, using separate filler metal in TIG welds is optional and depends on the project. As welding continues to evolve, its standards and norms also improve with time. New possibilities constantly arise, allowing us to weld new material combinations while guaranteeing and improving weld strength and process safety. With the recent developments in hybrid welding, we can only expect welding technology to continue shaping the future of engineering.