Automotive hail damage repair advices? The first step to performing a dent repair without using paint involves assessing the dent itself and determining if a paintless dent repair is even possible. According to most experts, 80 to 90 percent of dents can be repaired using PDR techniques. However, there are a certain percentage of dents that are impossible to repair without following it up with a paint job. The following types of dents usually fall into this “non-PDR” category: Very deep dents – Even very large dents can be repaired using PDR if the dent is fairly shallow. However, if a dent of any size is pushed in too far, the metal can’t be bent back into place without damaging the paint and requiring repainting.
So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.
1st let’s begin with some car paint care tips: Undercoating: Although waxing the car and polishing it produces good results, you need to protect the car from long term damage by undercoating and rust-proofing it. When the car metal is oxidized, rust sets in and destroys the surface of the car. To avoid this, you should consider rust-proofing the vehicle, particularly if you reside in a state where the humidity is high.
We recommend going to a professional repair service to avoid a lot of extra costs. Meet EvidentPDR in Colorado. Leo has over 15 years of experience with print services, vinyl wrap, window tinting, graphic design, and physical advertising. After many years of working with Pinnacle Signs, he then founded LD Wraps for 5 years, where he acquired many large accounts in Colorado Springs, everything from designing for local breweries, news stations, and real estate. Ben and Leo met through several business interactions, where Ben asked Leo to design several vinyl decals, stickers, signs, and banners you see in our shop. Discover additional info on Auto dent repair Colorado Springs.
This technique is popular among automotive enthusiasts when it comes to the removal of small dents. The idea is simple: heat will inevitably cause the metal surface to expand and (hopefully) pop the dent out. Remember that the more time the car spends time under the sun, the better this technique will work. Use a plastic and/or leather conditioner for the car’s interior, so as to not damage it while exposing the car to maximum sunlight. If the sun’s heat isn’t particularly strong that day, a simple hair dryer could be used in conjunction with the sun to concentrate the heat to a specific area. Point the hair dryer to the dented area for two-minute intervals until the dent pops out. Be careful not to touch the hot lip of the hair dryer on any painted surface. A two-to-four inch gap between the dryer and the surface is recommended.
For small dents on your car hood, a car dent repair kit may be a simple and inexpensive solution. You can easily find these kits at any local auto supply store and they are very user-friendly. Each kit often includes a knockdown tool, a glue gun and many stems for different sized dents. You may be surprised at the way the kit works and the professional result it makes. But we do recommend this kid for small dents only. For deep, large dents, it is better if you take your car to garage as the repair kit can not fix them and even cause more damage.
Use Hot Glue, Wooden Dowels, & Screws: When you attempt to take out dents yourself, you always put the risk that you might further damage your car, whether you make the dent worse or chip the paint. A safe way of trying to take out big dents on your car is by using several wooden dowels, a few screws, and a hot glue gun. Simply place two nails into each side of the dowel and put the hot glue on the bottom. Place the dowels glue-side down in areas around the dent, repeat as many times as needed to cover the area, let them dry, and pull each one out until the dent is gone.
If you want to polish your car and are considering buying a buffer, you can see my simplified approach to car polishing for the true beginner to achieve professional results. As the saying goes, “an ounce of prevention is worth a pound of cure”, and your car is no different. If you are just consistent with the basic instructions I have provided here, your car will not only look fabulous year after year, but will retain much more of its original value when you are ready to sell. Want to save your time and maximize your car detailing efforts. Unless you are a die hard car enthusiast, I actually recommend you find a quality, 100% cloth or hand wash, and take your car there at least every 2 weeks and let the crew there perform the grunt work of car washing.