Author: Marie Poppins

Buy online MIG welders

A few tips about welding equipment, MIG and TIG welders, plasma cutters. What factors should you consider when determining a budget? You may already have an estimated budget in mind. The type of welder you purchase should be suited for the specific functions you require as well as the projects you will work on the most. Think about your end goal and consider opportunities to expand the usefulness of your welder. Will you want more power or amperage in the future? It is important to take note of the varying amperage and power requirements as well as the duty cycle necessary to achieve the most effective and economical operational results for the projects you’re looking to complete. In addition to the cost of the welder itself, don’t forget to include costs for the accessories and supplies you’ll need to operate your new welder. This includes welding protection (helmet, gloves, jacket, etc.) as well as gas and consumables.

Looking for Plasma cutters? Welding Supplies Direct & Associate company TWS Direct Ltd is an online distributor of a wide range of welding supplies, welding equipment and welding machines. We supply Plasma Cutters, MIG, TIG, ARC Welding Machines and support consumables to the UK, Ireland and Europe.

One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.

The welding setup, welder settings, and electrode selection will impact how fast welders can work. Industrial welders invest time in planning the size and shape of their welding areas, how parts are laid out, and how they supply their shielding gas. Testing settings or an electrode on a piece of scrap metal, especially for a beginners, will save time in the long run. Learn more about setting up an efficient shop here. Welding Downhill Increases Welding Speed: While welding downhill is a faster way to weld, it’s not as strong as welding uphill. On most projects it’s not worth sacrificing strength and durability for the sake of welding speed. However, if the metal is thin enough, then welding downhill won’t make the weld weaker and may even be the correct technique for the job. Learn about uphill and downhill welding and see these diagrams of vertical and downhill welding.

How to pick a welder tips: MIG wire inch button: A great feature. This will save you wasting your shielding gas when feeding wire through at the start of a new reel. Gas purge button: Another nice option. Save yourself some MIG wire, when you’re setting your gas flow. Burn back facility: Not all machines have this externally, buy it’s good to be able to trim the burn back to the wire according to the application & operator. Selecting the correct amperage machine: Generally, you should work on 35-40 amps per 1 mm diameter of material to be welded.

Business Name: Welding Supplies Direct & Associate company TWS Direct Ltd
Website: https://www.migwelders.ie/
Address : TWS Direct Ltd. Unit 1 M54 Space Centre.
Halesfield 8. Telford. Shropshire. TF7 4QN
Phone : +44 (0) 1952 582 260
Email: sales@weldingsuppliesdirect.co.uk
Office Hours: Mon – Frid / 9:00Am – 17:30pm

By Shopping

What can you see in New Zealand and eTA application

What can you see in New Zealand and eTA application : Rudyard Kipling called Milford Sound the “eighth wonder of the world,” and if you visit this region of New Zealand, you’ll see why. Formed by glaciers during the Ice Age, the landscape around Milford Sound still bears evidence of its creation in the form of epic scenery: Cliffs rise from fjords crowned by mountains and waterfalls. The best way to see Milford Sound is via boat. Take a sightseeing cruise on the fjord to see waterfalls and wildlife such as dolphins and penguins. Or navigate the waters under your own steam on a kayaking tour. Once you’ve experienced the water from the surface, go underneath with a visit to the Milford Discovery Centre and Underwater Observatory. This is the only floating, underwater observatory in New Zealand, and visitors can go more than 30 feet deep (while staying dry) and get 360 degrees of the underwater environment.

Extending to almost the entire length of the South Island, the Southern Alps mountain range is the highest in Australasia. It is home to Aoraki/Mount Cook, Mt Aspiring, Mount Tutoko, along with various other mountains, glacial lakes and forested wonders. Located on New Zealand’s Hauraki Gulf, Tiritiri Matangi Island is an incredible wildlife sanctuary that’s home to various native and coastal birds. It is a predator-free island, where a number of threatened and endangered species have been introduced and protected from extinction.

Kaikoura, This small coastal town on the South Island is a haven for seafood lovers. You can spot fur seals, dolphins, sperm whales and albatrosses off the shore, then indulge in a feast of fresh crayfish, mussels, blue cod and more. Land lovers can take a wilderness walk through the untamed and dramatic Kaikoura forest. Franz Josef glacier, This glacier, located within Westland National Park in the southwest, is one of the world’s most accessible. Visitors can walk right up to the foot of the massive glacier or take a helicopter ride over the dazzling Ice Age remnant. Together with Fox Glacier it is one of South Westland’s major drawcards for tourists.

Who can apply for NZ eTA application? Citizens from eTA New Zealand eligible countries can obtain an eTA for New Zealand (NZ) by completing a simple online application form. The New Zealand eTA (NZ eTA) visa is valid for a period of 2 years and can be used for multiple visits. Applicants can apply for NZ eTA from their mobile, tablet, PC or computer and receive it in their email inbox by using this New Zealand eTA application form. See more details at New Zealand eTA.

All the follow up of the application is managed by our experts, and approved eTA documents are sent by email with detailed information and tips on how to use the eTa in order to successfully enter the destination country. We are a private website and are not affiliated with the New Zealand Government. Our services have a fee for our professional travel support. Applicants may process their application directly through the New Zealand Government website for a lesser fees.

A World Heritage Site, Fiordland National Park protects some of the most spectacular scenery in the country. Glaciers sculpted this dramatic landscape carving the famous fjords of Milford, Dusky, and Doubtful Sounds. Visitors here can explore gushing cascades, offshore islands, virgin rainforests, vast lakes, and craggy mountain peaks. Not surprisingly, the park is a haven for hikers with some of the country’s best walks, including the famous Milford Track. Sea kayaking is a popular way to explore the fjords, and visitors can also enjoy a scenic flight over the park for a bird’s eye view of its staggering beauty.

By Business

Personal injury attorneys

Personal injury attorneys. Here are some tips for improving your chances. Most people are familiar with the phrase that states that everything you say can and will be held against you in a court of law. Unfortunately, not all people realize that this phrase also applies to what you say on social media. If you’re claiming devastating injuries, but your Facebook page tells a different story, it can ruin your case. The other side is watching, and your best bet is to keep quiet and let your attorney do the talking. It’s also a good rule of thumb not to talk about any aspect of your injury case with anyone, or anywhere until a settlement is reached.

If in your first conversation, the adjuster makes an offer so low that it is obviously just a negotiating tactic to see if you know what your claim is really worth, do not immediately lower the amount you put in your demand letter. Instead, ask the adjuster to give you the specific reasons why the offer is so low. Make notes of the conversation. Then write a brief letter responding to each of the factors the adjuster has mentioned. Depending on the strength of any of the adjuster’s reasons, you can lower your demand slightly, but before lowering your demand very far, wait to see whether the adjuster will budge after receiving your reply letter. The next time you speak with the adjuster, begin by asking for a response to your reply letter. The adjuster should now make you a reasonable offer upon which you will be able to bargain and arrive at a fair final settlement figure.

You may be entitled to other insurance benefits. If you have PIP, auto med pay, group or private health insurance or are covered under a spouse’s or parent’s insurance, your attorney can coordinate submission of all collateral insurance claims to maximize your total recovery. Never settle your claim before its time. It sometimes takes many months to settle a claim. Occasionally a claim may take a year or longer to be resolved. In fact, it is not in the accident victim’s best interest to settle certain types of claims too soon because it often takes a long time for serious injuries to become evident or for treatment or surgery to provide the maximum benefit to the injured party.

Personal injury lawsuit and social media : Do not publish anything relating to physical activities (including travel) while your case is ongoing. Despite often being the exact type of update you’d like to share with friends, publishing updates about your injuries and treatment can potentially damage your case. Updates can be taken out of context and occasionally viewed in a way that diminishes your potential settlement. As a result, publicly discussing any facet of your treatments isn’t worth the risk.

Every time you read our content you will feel comfortable along the journey as we describe each detail as best we can to help you with personal injury legal actions you may need help with, we are on your side and we are here to help with your legal issues! When you suffer from an accident or an injury done by others, then you are allowed to recover the compensation from the person that is responsible for the injury or the accident. This made a personal injury case which allows you to enforce your rights and claim the losses that have occurred whether it is of money, land, or life. See extra info on personal injury lawyers.

By Legal

Instrument hobby bobbleheads online shopping

Let’s begin with a brief history of bobbleheads. 2000 : Bobbleheads seemed to be 20th century relic by the turn of the century until a promotion by the San Francisco Giants brought the bobblehead back to the public eye. The Giants offered a Willie Mays bobblehead to the first 20,000 visitors on May 9th to celebrate the 40th anniversary of Candlestick Park, which was the last year of the Giants playing at that stadium. New variations of the bobblehead were made including the mini-bobblehead, bobble computer sitters, bobblehead banks, and even bobblehead air fresheners. The Guinness Book of World Record for largest bobblehead was set for a bobblehead in the likeness of TV show host Chuck Woolery. The bobblehead weighed 900 pounds, was 11 feet tall and was originally displayed at the McCormick Place, Chicago, Illinois.

How are bobbleheads made? There are all types of bobble heads and they’re made from several types of materials. Generally, the most common bobble heads are made from resin and plastic. There are also ceramic and wooden bobble heads, but they are in the minority of the products currently produced. The resin bobble head dolls are solid and generally allow for greater details and finer contouring of the body. Plastic bobble heads are cast from a mold, but not all plastic bobbing heads are the same. Some styles rely purely on the mold as the entire product with the appropriate paint colors added. Our most popular bobble heads use a plastic inner shell that are not solid and are covered with felt cloth. The felt adds a layer of detail, a layer of feeling, and an additional layer of strength to the bobble head. With our bobble head animals, you’ll find that the eyes are made of plastic and some vary from completely solid colors to an eye complete with color and pupil.

In June 2012, the TBS talk show ‘Conan’ went to film in Chicago and produced one of the largest bobble head dolls ever documented. The Conan O’Brien Bobble Head stood at 16 feet tall! In 2016, there were many terrific MLB bobble head giveaways that focus on team mascots to legendary Dodgers broadcast Vin Scully. Both major league and minor league baseball heavily use bobble head doll promotions to drive attendance. For 2017, MLB teams plan no let down in the size and scope of bobble heads. Teams from the Mets with their Noah Syndergaard Thor themed bobble head to the Angels with three different Mike Trout bobble heads throughout the season aren’t letting up with promotions throughout the league each and every week.

In 1960, Major League Baseball decided to give away a series of papier-mache bobblehead dolls for each team with the same cherubic face and imported from Japan. That same year World Series was held and first bobblehead dollswere made specifically for players but they still had the same faces. The players that had bobbleheads made for them were Roberto Clemente, Mickey Mantle, Roger Maris, and Willie Mays. Beside of players, teams made and gave away as souvenirs bobblehead dolls in the shape of their team mascots. When material of making bobblehead dolls was changed from papier-mache to ceramic they were made in likeness of players of other sports too and of cartoon characters. The Beatles bobblehead set, which was made in the next decade is still a very valuable collectable. In time production and interest for bobblehead dolls again waned and by 1970s it almost disappeared completely.

Alexander Malcolm would become one of the largest bobblehead sellers and a key figure in the history of bobbleheads, producing 48-49 million of these sentimental nodding heads. But he did not know it at the time when he sat down at a business meeting with the San Franciscio Giants during the 1990s. He was just hoping to sell some sort of promotional item for them. When Malcolm asked what they were looking for, The San Francisco Giants replied, “bobbleheads”. Malcolm agreed to provide thousands of Willie Mays bobbleheads to the professional baseball organization to be passed out to their fans for free. Malcolm went to work, but did not know he could get away with using the traditional cartoonish boy bobblehead. Instead, he made a much more real version of Mays (although Mays would disagree). So, on May 9, 1999, to celebrate the anniversary of Candlestick Park, the last year the Giants would play at this stadium by the bay, 20,000 visitors each received the Willie Mays bobblehead. It was a success! The crowd loved the semi-life-like yet cartoonish novelty item. That one game made way for the bobblehead era revival. The next year, eight Major League Baseball teams had bobblehead giveaways. And Malcolm’s small business in the 1990s flourished into the global enterprise it is today.

We offer variety of bobblehead dolls and thousands of bodies’ style with high quality material –polymer clay which lasts lifetime. Custom bobbleheads, like, female custom bobbleheads, male custom bobbleheads, holidays custom bobbleheads, sports custom bobbleheads, pets custom bobbleheads, accessories custom bobbleheads.Our products are applauded for their extremely like and high quality. Read extra details on personalized bobbleheads online store.

By Shopping

Why rayming is the best for pcb

Let’s discuss about How do pcb assembly cost calculator. His first step was to assemble his BoM and send it with the Gerbers. He is at pains to stress that the BoM is key to the whole project, and getting it right with the correct packages and more than one source for each component is critical. The board house first charged him L32.05 ($41.76) to make his PCBs and stencil, and assess his BoM for a build quote. A few days passed, and then he had a quote for assembly, L61.41 ($80). He placed the order, the board house processed it and made the boards, and in due course his working PCB modules arrived. This might sound at this point like an unexciting saga, but its very smoothness is the key to what makes it interesting. Those of us who have wondered about the risks involved in taking up such a service need to hear stories like this one as surely as we do stories of failure, because without them we’re flying blind. Whether £93.46 ($121.76) for ten small boards represents good enough value is another matter, but if surface-mount soldering is not your thing you might be interested to follow [Alexander]’s example. After all, it wasn’t so long ago that getting a cheap PCB made in China was a similar leap of faith.

This industry provides quality assured flexible PCB, which are best in the market. Their manufacturing process starts from gathering all the raw materials for the manufacturing of Flexible PCB and then this step is followed by the designing of the PCB. After the designing process is over, the product is then developed, after the completion of each phase a testing team is present. This testing team tests the products for the best output and features. If all the requirements are not met, then the developing team again redesigns the board and again the testing team tests the products. This work goes until the desired output is got from the Flexible PCB Board.

For the purpose of soldering there are only few things which are very essential for this process. They include a solder, an soldering iron, any forms of filler metals, a stand to keep the solder and a sponge or a cloth for the purpose of holding and cleaning the solder. Different types of Soldering tips are used for the purpose of Soldering. Conical and pointed tips are used for the Soldering purpose. Conical tips are used for Soldering in the most precision way and the pointed tips are generally used to heat small areas in the electronic devices and also in the PCB Boards. Soldering is almost used in all the manufacturing industries, starting from the electronic industries to the musical manufacturing industries. They are also used in the plumbing techniques. These plumbing methods are permanent but yet reversible. They are also used in the music instruments manufacturing industries for the purpose and also in the manufacture of of jewelry components. Most precise jewelry designs are done by using the soldering methods.

When it comes to Ray PCB, you will be going to experience the high quality services for sure. From soldering to assembling process in any PCB boards, you can find the best services. Well, in order to offer the best quality products to your customers make sure to choose the good basic stuff. At this stage, choosing the high quality PCB assemblies is always necessary. If these things are managed to handle, then there could be a chance of holding your customers for all the time. This is what each and every business person should be thinking of it. In case, if you are struggling to find the right ways of searching for best PCB manufacturing factory, then make sure to get notifications from experts that whenever required as per convenience. So, choosing the high quality service company is always necessary for your products that whenever planning to develop the products. Read more details on https://www.macobserver.com/sections-four-layer-pcb/.

By Business

Coffee shop online

Let’s get informed about coffee, coffee types and flavors. Cappuccino : Possibly the most popular type of coffee in the world, a cappuccino consists of three layers (kind of like a cake). The first is a shot of espresso, then a shot of steamed milk, and finally the barista adds a layer of frothed, foamy milk. This final layer can also be topped with chocolate shavings or powder. Traditionally, Italians would consume this type of coffee at breakfast. Espresso : To make an espresso, shoot boiling water under high pressure through finely ground up coffee beans and then pour into a tiny mug. Sounds simple right? Well, it’s surprisingly difficult to master. Espressos are the purest coffee experience you can get, and while they’re not for everyone, it can be a truly singular drinking experience when you find a good brew.

Two less common types are Liberica and Excelsa, which are rarely seen, especially in the United States. The former is grown exclusively in the Phillipines and is not imported at all into the States. On the other hand, the latter (which is often considered a genus of Liberica beans) only makes up about 7% of the world’s consumption and are grown in Southeast Asia.

Typica is your “typical” Arabica. It’s a variety that encompasses a number of the most popular and most sought after regional coffees including Kona, Java, Jamaican Blue Mountain, and more. This variety started in Yemen before being spread far and wide through trade. It first made it to Malabar India and Indonesia before eventually reaching the West Indies. Some subvarieties of Typica include Sumatra, Bergendal, Rume Sudan, Amarello de Botancatú, Blawan Paumah, and Java Mocha. Also, there are a number of Typica mutations, including Mokka*, Pluma Hidalgo, Creole, Ethiopian Harrar, Blue Mountain, Villa Sarchi, Ethiopian Sidamo, Ethiopian Yiragacheffe, San Ramón, and Sidikalang (just to name a few). Bourbon is probably one of the most common sub varieties of Typica. It got its start in the early 1700s when the French brought an Arabica Typica plat to the island of Bourbon (now Reunion). A slight mutation occurred and the variety eventually spread across Central and South America. These plants are popular because they produce more coffee cherries than other Typica varieties. Sub-varieties of Bourbon include French Mission, N39, Mayaguez, Arusha, Jackson, K20, Kenya Selected, and SL35 ; and Pointu, Semperlorens, Caturra, SL34, Tekic, and Pacas are mutations from this variety.

Lungo – Lungo is often confused with Americano, but it’s not at all the same. Lungo is a long shot prepared by extracting double the amount of water with same amount of coffee grounds. In figures, it means, 50 ml of water is extracted with 7 grams of coffee. This results in extraction of more caffeine, but with dissolved off-notes of coffee. It’s a less popular drink but it’s a preferred drink for people who demand more caffeine. Caffe Crema – An extra long espresso drink served in Northern Italy, Germany, Switzerland and Austria. It has different flavor profile than related drinks like Lungo and Americano due to different extraction process. Rough brewing ratios of ristretto, normale, lungo, and caffè crema are 1:2:3:6 and the average water part per shot is 6 oz (180ml). Cafe Zorro – This is a double shot of espresso that is added to water in a 1:1 ratio. See more details on Coffee Shop.

By Food

How to: upgrading to Drupal 8

Upgrading a website script version is one of the highest risk procedure a webmaster has to deal with when managing a website. Migrating from Drupal 7 to Drupal 8? Here is a small guide with various details. Let’s start with basic info : Note that you don’t need to know anything about PHP to build a site in Drupal. When you search (preferably on Google) for a solution to your latest Drupal problem, a lot of the pages that come up will be providing snippets of PHP code. This is not the correct help information for you, the Drupal newbie. This is for technically competent people who are able to build their own modules and stuff like that. If you look at the other pages thrown up by your search, you will probably find an answer to your problem which involves working within the existing Drupal core and modules. That means, a solution you can implement using menus and tickboxes and whatnot, without needing to mess around with code.

The very first thing you should do is to make a local version of the website. This is an essential step because making changes to a live website is very risky and is never a recommended practice. This way, if anything does go awry, your actual website will remain safe and functional. After clicking Continue, you will be brought to the screen in the following screenshot. Enter all the required details such as your existing website’s credentials, the database location and the location of your website files.

Upgrading is the process of moving your site from a previous major version of Drupal to a newer version, for example from Drupal 7 to Drupal 8. This consists of upgrading the codebase to the appropriate version and then migrating the data from your old site into the new one. Drupal 8 core contains two modules to help facilitate this process: Migrate Drupal and Migrate Drupal UI.

The steps above outline how to get a distribution minimally installed on an existing site. But you’ll still have a lot of work to do to reconcile your existing site content and structure with what has been created by the distribution. Here are a few tips to get you started–but you should begin with the assumption that there will be lots more you’ll discover and need to fix. Roles. Many distributions will create one or more custom roles. Examples include contributor, editor, and administrator. If any of these roughly correspond to existing roles on your site, delete the roles created by the distribution and rename the existing ones to use the distribution role names. For example, if your site has a role called “site administrator” and the distribution has created a role called “administrator”, delete the newly created “administrator” role and rename “site administrator” to “administrator”. After adjusting the role names, visit admin/config/people/accounts, ensure the “administrator” role is selected as the “Administrator role”, and save the form. Consolidating the roles in this way will get you the functionality of the distribution’s roles and permissions while maintaining your existing users’ role allocations.

If you already have a Drupal website that has a considerable amount of content or a large number of users or has custom functionality you want to keep, though, you might want to try directly upgrading the site to use the distribution. Doing so could save you a lot of time in migrating content. But it will also raise a number of challenges. Upgrading to a distribution is probably something you should try only if you have the skills and time needed to do troubleshooting and some custom data work.

There are several tips and best practices to follow to help you prepare for the upgrade. Still, since this is such a complex process, we highly recommend getting members of your development team involved from the beginning, which will help ensure the upgrade goes as smoothly as possible. Upgrading to Drupal 8 is more similar to building a new website than previous Drupal updates were, meaning that you should never perform the upgrade to Drupal 8 on a live site. It’s also strongly recommended that you create a backup of your live site so that if anything goes awry, you can quickly roll the site back to an earlier version while you figure out what the issue is. Read extra info at Drupal 8 Migration.

By Internet

How to lose weight advices

Huge weight is a big problem and people should watch it but also avoid dangerous diets. Here are some weight loss advices for safe weight loss. Think skipping meals is the key to a slimmer body? Think again. Research published in 2012 in the Journal of the American Dietetic Association revealed that eating more frequently—specifically eating three meals and two snacks in a 24-hour period—is positively associated with weight loss and weight maintenance.

Want to boost your weight loss? Start by leaving the car at home. Research published in 2012 in the American Journal of Preventative Medicine shows a significant link between commuting by car and increased weight gain, even among those who are otherwise physically active. So, if a distance is short enough for you to walk and you’re physically able to do so, go by foot whenever possible.

“Too many people start their fat loss plan without setting an end date or a realistic goal,” says personal trainer Leon Kew. “You need targets to keep yourself motivated, especially for situations when it would be easy to make bad decisions – when you get offered cake on a colleague’s birthday, it’ll be easier to turn down if you know you’re only two weeks from your goal. Set a finish date that you are 100% confident you can hit. There will inevitably be times where you’re tempted to go back to old habits – and having a specific goal, with smaller milestones along the way, can keep you on track.”

“The number one priority in any fat loss challenge is compliance,” says David Godfrey, performance director at One Performance UK. “If you can’t sustain the programme in the long term you’ll never achieve your goal – or you’ll simply rebound as soon as you do. Calculate your calorie target for the week and allow 10% of that to come from your favourite foods. Most people feel like they’re cheating when they eat their favourite foods, so incorporating them into your nutrition plan helps keep you on track without guilt or painful sacrifice. The psychological impact of this is huge.”

Ironman Foundation ambassador athlete Marcus Cook is proof that patience and perseverance wins every single time. Cook dropped from 489 pounds to 233 pounds in a year and a half after his close friend and boss died from cancer. “Before he died, he said, ‘I’m dying because I have an incurable disease, and you’re dying because you have a choice,'” Cook told INSIDER. “When he said that to me, I changed everything about what I was doing and made an about-face turn.” To get started, Cook committed to doing something new every day, a tip he often gives to others. “I realized that my weight didn’t appear overnight, so it wasn’t something that I could change in one day,” he said.

Now that it’s summertime, you’ll want to take advantage of all that natural sunlight. One 2017 study published in Scientific Reports found that fat cells exposed to light stored less fat than those kept in the dark. However, just because a little light is good for you doesn’t mean you can’t overdo it: More than 15 minutes a day without sunblock can increase your risk for skin cancer, so be careful!

“Whether you’re trying to lose weight or manage your cholesterol, the 2019 Best Diets rankings provide each person a chance to evaluate what eating plan will work best for them and their particular needs,” said Angela Haupt, Assistant Managing Editor of Health at U.S. News. “By profiling and providing in-depth data on more than 40 diets, as well as sample meals, consumers can rely on U.S. News for the tools they need to feel empowered to make well-informed lifestyle and wellness changes.” As we say, there’s no one diet to suit every single person. What will work for someone might not suit your particular goals or lifestyle. Read more details on Lose Weight Fast.

By Health

Top quality welding supplies

Some tips about welding equipment, MIG and TIG welders, plasma cutters. Welders with a higher power output can work with thicker metals, but higher voltage welders will require special power supply set ups—either generators or appropriate power outlets. A welder with lower voltage in the 100’s will not be able to handle heavy duty jobs, but it can be plugged in and operated from any outlet. Any welder with power over 200 cannot run off a typical power outlet and will naturally cost more to run. In addition, welders will either run an alternating current (AC) that reverses itself at regular intervals or a direct current (DC) that flows in one direction and does not reverse itself. DC offers a steady rate of energy that leads to hotter temperatures and deeper weld penetration. AC welders usually cost less than DC welders, but the available electrodes are far more limited for AC. In fact, DC welders are more costly but remain popular because their higher power offers a wider selection of electrodes and a number of working advantages such as: simple arc striking, better penetration, and improved control. Welders who expect to work on a wide variety of projects may want to consider an AC/DC combination welder.

Searching for Welding equipment? Welding Supplies Direct & Associate company TWS Direct Ltd is an online distributor of a wide range of welding supplies, welding equipment and welding machines. We supply Plasma Cutters, MIG, TIG, ARC Welding Machines and support consumables to the UK, Ireland and Europe.

In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode.

The welding setup, welder settings, and electrode selection will impact how fast welders can work. Industrial welders invest time in planning the size and shape of their welding areas, how parts are laid out, and how they supply their shielding gas. Testing settings or an electrode on a piece of scrap metal, especially for a beginners, will save time in the long run. Learn more about setting up an efficient shop here. Welding Downhill Increases Welding Speed: While welding downhill is a faster way to weld, it’s not as strong as welding uphill. On most projects it’s not worth sacrificing strength and durability for the sake of welding speed. However, if the metal is thin enough, then welding downhill won’t make the weld weaker and may even be the correct technique for the job. Learn about uphill and downhill welding and see these diagrams of vertical and downhill welding.

How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).

Business Name: Welding Supplies Direct & Associate company TWS Direct Ltd
Website: https://www.migwelders.ie/
Address : TWS Direct Ltd. Unit 1 M54 Space Centre.
Halesfield 8. Telford. Shropshire. TF7 4QN
Phone : +44 (0) 1952 582 260
Email: sales@weldingsuppliesdirect.co.uk
Office Hours: Mon – Frid / 9:00Am – 17:30pm

By Business

Divorce support

Divorce is a very hard situation and nobody should get through it alone. Help my divorce You know that thing that you found shocking? The line your spouse crossed? That act of betrayal that you and everyone you know is shocked and appalled by? The court doesn’t care. Short of provable acts of abuse or addiction they don’t give a shit. Ultimately, the court is there to divvy up property not mete out vengeance. You’re never going to have that Perry Mason moment where your ex gets on the stand and has to admit to his or her douchebaggery. They just want to figure out who’s getting the couch and where the kids go on Christmas.

If you have debt in your name, like credit cards or student loans, you will want to pay those debts down as much as possible before a divorce. Most American families spend close to their entire income, if not more, and when one household becomes two, there is often not enough money to pay the both sets of expenses unless something changes. You may have to cut down disposable purchases, sell your car and get a less expensive model, or maybe sell the house. If your spouse does not voluntarily support you and the children, your remedy is to ask the Court to order support. You will not have a good prediction of any of this and you will not know the answers for sure until the agreement is signed or the judge makes a ruling. But, the point is to think about it and identify problems and possible solutions. Then take the actions that you can take and avoid missteps.

People who treat their divorce like a business transaction, and to the extent possible, control their emotions so their decisions are based on their best interests and not their hurt feelings, fare much better. For instance, some people might argue endlessly over values of certain assets, when in reality, if they just compromised they would save in attorney’s fees and time. Sometimes people do prioritize what is most important and spend time and energy arguing over assets that might not have a significant value while ignoring the more valuable parts of the marital estate. Sometimes people get hung up over how something is characterized — for example, they might agree to a one-time cash payment to their spouse but balk if that same payment is labeled “attorney’s fees.” Taking a step back, looking at the big picture, and understanding the cost of fighting as well as potential risks and rewards will serve anyone well during a divorce.

The biggest mistake divorcing spouses can make is being in the dark about finances. If your spouse has always handled all of the financial decisions in your household and you don’t have any information about you and your spouse’s income and assets, your spouse will have an unfair advantage over you when it comes time to settle the financial issues in your divorce. If you suspect your spouse is planning a divorce, get as much information as you can now. Make copies of important financial records such as account statements (eg., savings, brokerage, and retirement) and all other data that relates to your marital lifestyle (eg., checking accounts, charge card statements, tax returns).

We are an online divorce community and one stop divorce shop for all things divorce. We incorporate a marketplace specializing in selling items associated with one time dreams with our Ultimate Divorce Resource Directory full of secondary divorce services and a community of like-minded individuals, who we invite to connect with each other for support, friendship, dating and networking. See more info at Divorce community.

By Legal