Category: Industrial

Excellent 80a solar charge controller manufacturer? The FLEXmax family of charge controllers is the latest innovation in Maximum Power Point Tracking (MPPT) charge controllers from Fangpusun. The innovative FLEXmax MPPT software algorithm is both continuous and active, increasing your photovoltaic array power yield up to 30%compared to non-MPPT controllers. Thanks to active cooling and intelligent thermal management cooling, both FLEXmax charge controllers can operate at their full maximum current rating, 60 Amps or 80 Amps respectively, in ambient temperatures as high as 104°F (40°C). Fangpusun 80a MPPT solar charge controller wholesale, contact us. Discover additional details on https://www.pvsolartech.com/mppt-solar-battery-charge-controller-150v-80a-flexmax-mppt-60-80. Fangpusun is mainly running the work of the solar charge controller. The solar control series is available in a vast selection of types and specifications like Fangpusun MPPT charge controller, PWM solar charge controller, and solar charge controller accessories. Closely following the industry trend, Fangpusun charge controller manufacturers employ advanced production equipment and production technology to produce solar controllers. The item receives favors from the majority of customers for the high quality and favorable price.

When a solar charge controller is not able to recharge the battery to its full capacity within one day, the result is often that the battery will continually be cycled between a partially charged state and the ‘end of discharge’ state. This mode of operation (no regular full recharge) will destroy a lead-acid battery within weeks or months.

Usually the largest single cost factor is lighting. Obsolete light bulbs only use about ten percent of the electricity to make light. 90 percent are lost as heat. They produce heat rather than light, because they are based on a glowing filament made of tungsten. Modern LEDs use almost all of the electricity to make light. You can clearly notice this from the fact that they stay cool, i.e. there is much less loss. A good LED needs about a tenth of the electricity to produce the same amount of light. And because it does not heat up so much, it lasts much longer. And: The price of LEDs has come down so much, that exchanging them for regular light bulbs pays off within one or two years. The same is true for industrial lighting systems which often use mercury vapour lamps. These, too, use up a lot of electricity and can easily be replaced by LEDs.

The initial cost of purchasing a solar system is fairly high. Although the UK government has introduced some schemes for encouraging the adoption of renewable energy sources, for example, the Feed-in Tariff, you still have to cover the upfront costs. This includes paying for solar panels, inverter, batteries, wiring, and for the installation. Nevertheless, solar technologies are constantly developing, so it is safe to assume that prices will go down in the future.

Fangpusun is mainly engaged in the business of solar inverter and other battery accessories product series. Fangpusun battery accessories products like 12v battery monitor and battery balancer are manufactured in strict accordance with relevant national standards. Every detail matters in the production. Strict cost control promotes the production of a high-quality and priced-low product. Such a product is up to customers’ needs for a highly cost-effective product.

Fangpusun solar power inverter is mainly engaged in the business of off grid on grid inverter series. The solar power inverter has the following advantages: well-chosen materials, reasonable design, stable performance, excellent quality, and affordable price. Such a off grid on grid inverter product is up to the market demand. The solar power inverter runs a comprehensive supply system and after-sales service system. We are committed to providing excellent off grid power inverter and on grid power inverter product service for the majority of customers. Fangpusun is a maturer inverter manufacturer for more than 10 years, we provide top-quality solar power inverter. Best PV solar inverter company, welcome to contact us. Read more details on pvsolartech.com.

Top Oxford welders online shopping Ireland 2021? Ireland market pick: Thinking to buy for the excellent ? The Forney Easy Weld 140 FC-i is a great MIG welder for home use. The “FC-i” in the name means “Flux Core inverter.” Inverter technology is lighter than traditional transformers used in most welders, meaning this welder delivers 140 amps even though it only weighs 19 pounds. The one thing this welder doesn’t offer is true MIG capability. Flux core wire doesn’t deliver the same clean, indestructible level of welding as a gas-shielded arc. It provides shielding by evaporating flux. For the average home welder, the difference is minor. However, if you need to weld aluminum or stainless steel, flux core wire isn’t up to it and you’ll need to find a MIG-capable machine. The 140-amp rating is about as hot as you can get without stepping up to 220 volts. That’s enough to weld 1/4-inch steel. The duty rating on this machine is 30 percent at 90 amps, pretty astounding on a machine in this price range. There’s probably not a MIG welder in this class that has more satisfied customers, a big reason it’s the Weld Guru Weekend Warrior selection for Best MIG. If you don’t have a lot to spend, then I would recommend taking a look at our cheap MIG welders for under $500 guide. Read additional details at https://www.weldingsuppliesdirect.ie/. The story of ESAB is the story of welding. When our founder Oscar Kjellberg developed the world’s first coated welding electrode in 1904, he launched a company whose innovation and uncompromising standards have helped create the history of welding itself. For more than 100 years, ESAB has been powered by the will to continuously seek new and improved ways of serving our customers. This has made ESAB a world leader in welding products and advanced cutting systems. In 2012, ESAB was acquired by Colfax Corporation, one of the world’s leading diversified industrial manufacturing companies. Colfax, like ESAB, is a solidly customer-focused company that places strong emphasis on constant innovation and improvement. From the firsts by our founder to our global growth, we take pride in what we’ve accomplished in more than a century. But we do so with a keen eye on the future. What can we do better? It’s only when we seek to build upon all we’ve learned, to perfect the innovations our customers count on to work confidently, and push ourselves and our company further that we can boldly face the future. This is how we continue to write the history of welding and cutting. At the end of the day, it’s not where you’ve been that matters most – it’s where you’re going. And for us, that’s forward.

How to pick a welder tips: Digital meters factory fitted: Great to have when you purchase and may be required for calibration requirements. To fit them down the line could be expensive. Drive rollers: Metal rollers are the best. Nylon & plastic ones will always wear away quicker. Drive block system: Four roll would always be first choice, but some of the lower amperage machines won’t have them & two roll therefore would be acceptable. Bottle trolley: If you want a stepped voltage machine to be portable, you’ll need one. If you have a full size industrial cylinder check that the running gear & cylinder rack are man enough.

LOTOS Technology is a California company that has only been around since 2007. Still, the LOTOS MIG is impactful and high quality enough to make it onto our list. This one is a versatile machine that is a fair price of about $400. And—provided that you have the necessary 240-volt outlet in your home—it can be set up in a matter of minutes. The duty cycle of this welding newcomer is impressive, and it can be utilized by pros and amateurs who have been continually impressed by the bang they’ve gotten for their buck. The LOTOS can weld steel and stainless steel from 18 gauge to ¼ inches and aluminum to 1/8 inch or thicker. Thermal overload protection doesn’t let this machine overheat, and infinitely adjustable heat/amperage as well as wire speed makes using the LOTOS simple. Check out the LOTOS MIG140 for a lower power alternative.

Delivery of parts to the welding station in an organized and logical fashion is also a way to reduce welding costs. For example, one company was manufacturing concrete mixing drums. In the fabrication process, the company produced 10 parts for one section, then went on to make 10 parts of another drum section, etc. As pieces came off the line, they were put onto the floor of the shop. When it was time to weld, the operator had to hunt for the pieces needed and sort through them. When the outside welding expert pointed out the amount of time being wasted in this process, the company started to batch each one on a cart. In this way, the pieces needed to weld one drum were stored together and could easily be moved to the welding area. This type of scenario is also true for companies that may outsource parts to a vendor. Though it may cost more to have parts delivered in batches, it may save more in time than having to organize and search through parts to be able to get to the welding stage. How many times each piece is handled in the shop may be an eye-opener to reducing wasted time. To measure such an intangible as this, operators are asked to put a soapstone mark on the piece each time it is touched – some companies are surprised to find out how many times a part is picked up, transported and laid down in the manufacturing process. In the case of one company, moving the welding shop closer to the heat treatment station eliminated four extra times that the part was handled. Basically, handling a part as few times as possible and creating a more efficient production line or work cell will reduce overall costs.

Our welding tables are to be self-assembled. This is an easy process; full instructions are provided. A wide range of tools are available for use with these tables and they are available as added optional extras in the custom options above. If you require guidance on which tool set would be the most suitable for you please feel free to call our helpful staff. *Please note that current lead times on these welding tables are 3-4 weeks, however if you require the table quicker please alert us and we will do our best to assist with your enquiry*

Some tips on welding equipment, MIG and TIG welders, plasma cutters. MIG welders use a wire welding electrode on a spool that is fed automatically at a constant pre-selected speed. The arc, created by an electrical current between the base metal and the wire, melts the wire and joins it with the base, producing a high-strength weld with great appearance and little need for cleaning. MIG welding is clean, easy and can be used on thin or thicker plate metals. Similar to MIG welding, flux-cored arc welding (FCAW)* is a wire-feed process but differs in that self-shielded flux-cored welding does not require a shielding gas. Instead, flux-cored wire is used to shield the arc from contamination. This is a simple, efficient and effective welding approach, especially when welding outdoors, in windy conditions or on dirty materials. The process is widely used in construction because of its high welding speed and portability.

The MIG welder performance depends on several parameters. The duty cycle is among them. It means the percentage of a 10-minute period the welder can work until it gets overheated. For example, “90A / 20%” means that a welder can work for 2 minutes at 90A before an 8-minute cooldown, i.e. 20% of 10 minutes. Now, about the material. We should note that the maximum thickness of a material a welder can handle depends on its amperage and welding wire thickness. Lastly, consider the thickness of the joint a welder can make in a single run. Household models can weld metal sheets from 18-gauge to 1/4” thick at the output of 70A – 180A, respectively.

If you know that your new machine comes with a 2-year warranty, it can take a lot of the stress off your shoulders if your device suddenly stops working. If you can’t find a MIG welder with an appropriate warranty and the right features, it’s often a good idea to choose something that has spare parts which are easy to find. Try not to buy anything that’s made outside of the UK. The price range may be more affordable but the parts would be harder to source. Look for a spool gun so you can weld aluminium. If you plan on using your home welder to weld aluminium, then you’ll need a standard spool gun. Aluminium can quickly become damaged and tangled with a typical welding wire feed spool, so a spool gun will ensure that you can get the best results from your DIY work.

The Hobart Handler 210 has the typical great quality Hobart build with durable parts that stand the test of time. The 210 is more suited to autobody repair and construction than the 190 and 140 and it welds up to 3/8 inch. It’s also a flexible unit with the capacity to weld off 115V and 230V. At under $1000 it’s lot cheaper than the Ironman 230 and is a wise choice if you’re looking for a welder that packs real power but isn’t the price of the heavy industrial welders. It you’re looking for the all round MIG package for power, versatility, quality and value for money, the Hobart 210 is our top pick. See our full review of the Hobart Handler 210 here.

Wall mounted fume filter units online shopping UK 2022: If you’re looking for the best portable weld fume extractor that would be small but powerful and also would come within an affordable price range, then BAOSHISHAN has the perfect device for you! This fume extractor absorbs all sorts of gases and dust generated by soldering and welding. The 1.2m smoking pipe is an added benefit to this fantastic device. Compact Design and Convex Tips. This small and compact machine has a state-of-the-art build quality that ensures high performance. The filters come with metal latches that seal off the fumes and don’t let any fume get out of the device. The pipeline’s sealing and stability are improved by fine convex tips. The machine comes with sturdy wheels that help to move the unit to anywhere you want. Its suction pipe is built with several small pipes which allow it to move around freely. See extra details at https://www.weldingsuppliesdirect.co.uk/welding-equipment/welding-fume-extraction.html. Similar to most products that are available in today’s market, this 1000l Adjustable Solder Smoke Absorber Remover features a carbon filter with foam and activated carbon. The amount of activated carbon in this product’s filter is at 0.02 lb. Furthermore, this product’s filter is perfect for absorbing any toxins within the workplace. On another note, the product’s low noise operation as well as its high-efficient fan are very impressive. Furthermore, this 1000l solder smoke absorber is easily adjustable to a certain absorbing angle. As a result, it is much more effective at doing its job.

Several advices about welding equipment, MIG and TIG welders, plasma cutters. A MIG welder uses a continually feeding spool of thin filler wire as an electrode fed by a wire feed gun to form an electric arc between a wire and the work-piece metal. This heats the work-piece metal and the electrode, causing them to melt and join together to create the weld. Mig welding can be either Gas or Gasless and each have benefits. Gasless welding is far more portable as there’s no gas bottle to carry around, saves cost on having to buy gas bottles and regulators, is easier on positional welds and can penetrate deeper than Gas MIG although the welding wire for a gasless MIG is more expensive than a gasless MIG. Gas MIG welding produces much cleaner welds with no slag or spatter, is slightly better on thinner metals and the welding wire is cheaper than gasless MIG wire.

The fume extractor is angle adjustable, which helps to keep the unit in the required position while working. Further, its filters use activated carbon and foam which has an extraordinary character to absorb moisture and flux toxins. It weighs only 2.3lb and hence is easy to port to any required position. The 30W powered motor is sturdy enough to work continuously for 24 hours and better performance; we recommend you do not use it consistently beyond 24 hours. The air flow level looks a bit low comparing to other models; hence the volume of flux abortion is not up to the mark. But, you can overcome the shortfall by using an active charcoal mask. Since the filter comes with active charcoal, it will absorb more moisture and dirt. It will make the filter pores get clogged soon; hence, you need to replace the filter at regular intervals.

Top welding handbooks: Always know what gas your wire requires — whether it’s 100 percent CO2 or argon, or a mix of the two. \While CO2 is considerably cheaper than argon and good for penetrating welds on steel, it also tends to run cooler, making it usable for thinner materials. Use a 75 percent argon/25 percent CO2 gas mix for even greater penetration and a cleaner weld, since it generates less spatter than straight CO2. Here are some suggestions for shielding gases for common types of wire: Solid Carbon Steel Wire: Solid carbon steel wire must be used with CO2 shielding gas or a 75 percent CO2/25 percent argon mix, which is best used indoors with no wind for auto body, manufacturing and fabrication applications. Aluminum Wire: Argon shielding gas must be used with aluminum wire, which is ideal for stronger welds and easier feeding. Stainless Steel Wire: Stainless steel wire works well with a tri-mix of helium, argon and CO2. Explore a few more info at https://www.weldingsuppliesdirect.co.uk/.

Best online provider to purchase span gas cylinder in UK: Tests have shown that the relatively narrow cross section of the pure argon shielded weld has a higher potential for gas entrapment and, consequently, can contain more porosity. The higher heat and broader penetration pattern of the helium/argon mixtures will generally help to minimize gas entrapment and lower porosity levels in the completed weld. For a given arc length, the addition of helium to pure argon will increase the arc voltage by 2 or 3 volts. With the GMAW process, the maximum effect of the broader penetration shape is reached at around 75% helium and 25% argon. The broader penetration shape and lower porosity levels from these gas mixtures are particularly useful when welding double-sided groove welds in heavy plate. The ability of the weld bead profile to provide a wider target during back chipping can help to reduce the possibility of incomplete joint penetration that can be associated with this type of welded joint.

Premium Oxford welders online shopping today? Ireland market choice: At just $99, the Goplus is a fantastic value considering what it is equipped to do. In fact, it is the most affordable welder on our list, beating out its competitors by hundreds or even thousands of dollars and putting it in a class of its own. For a budding hobbyist not yet sure if welding is for them, you can’t go wrong with the Goplus. After all, for $99 its welding thickness and the duty cycle is about what one would expect (don’t look to buy this welder if you want it for heavy duty use). The Goplus is light and compact when compared to most other welders. Flux core wire is included. It has four levels of easily adjustable current flow and ten levels of wire speed. The Goplus is able to weld steel and iron at below ¼ inches thickness.

Thinking to buy for the premium ? The Everlast Powermig 200 welder offers dual voltage inputs and weighs only 35 pounds due to inverter technology. It’s not only MIG-capable, you can also use it for flux core welding or as a stick welder. When your machine can stick weld and connect gas at the same time, all you need to buy is a connector block and you gain TIG ability too, although Everlast doesn’t say so. The Powermig 200 features a burn back control, automatically adjusting the wire length at restart. 200 amps can weld ?-inch steel in a single pass. Dual digital displays and a low-spatter arc control system are nice features in this price range. Preflow and Postflow improves weld quality, reducing porosity by starting the gas shield before the arc begins and cutting the gas off after the arc stops. The burn back control feature resets the length of the wire feed before you strike another arc. Another nice feature is the digital controls that give you a nice reading of exactly what your voltage and wire speed is. Everlast includes a gas regulator with this rig and backs it with a 3-year warranty. With stick capability and the ability to use it on either household or industrial power, this is quite a bit of welder for the money.

Our vision and our distinct set of values drive the success and spirit of our organization. At ESAB, under Colfax leadership, we live our values. As a premiere U.S. welding equipment manufacturer, our vision and values help us to make strategic decisions, allocate resources, and focus our choices every day, domestically and internationally. ESAB offers a world of products and solutions for virtually every welding and cutting process and application. We serve industries that serve the world. The Best Team Wins – Team-oriented, involved associates are our most valuable resource, and we are passionate about attracting, developing, and retaining the best talent. Living this value is done in three primary ways: 1. Building the right team – having the right people to do the job; 2. Creating the right environment – making sure that leaders create an environment where all associates can contribute, and 3. Getting the win – when you have the right people and right environment – it makes getting the win a lot easier!

How to pick a welder tips: Fan on demand: Lowers running costs and reduces contamination to internal components. The fan kicks in when it’s needed, rather than running all day. Printed Circuit board protection: If the machine’s PCB’s are protected from dust & kept away from the fan, reliability will increase. Some manufacturers’ have the parts that need cooling in a duct type housing & the PCB isolated separately. Step voltage settings: If you’re looking at step voltage conventional MIG with multiple power settings – “the more the better!” Discover more info on here.

Several tips on welding equipment, MIG and TIG welders, plasma cutters. TIG welding is similar to to a MIG welder as it uses an electric arc in the same was as MIG welding does but differs in a few ways. Instead of a continuous spool of consumable wire, a TIG welder uses long tungsten welding rods that are manually slowly fed into the weld puddle to join the metal. TIG welding requires gas, usually argon, to protect and cool the weld puddle from external contamination. TIG welding is more suited to welding thinner materials such as stainless steel and aluminium as you can get the power down lower to reduce the risk of blow through and can even weld two dissimilar metals. Suitable for tricky welds such as S curves but TIG welders are still capable of welding heavier materials depending on the machine. TIG welding takes more practice that MIG welding as the process is much more manual with controlling the torch, welding rod and gas by hand (and foot for the gas) but once mastered will produce the highest quality welds making it the better choice where perfect, precise welds are required but due to the manual process is the least productive.

Many companies get completely “bogged down” in the paperwork required to run a business. But with today’s latest technological advances, there are items that can be a great help. For instance, Lincoln Electric offers something called ArcWorks software which can document procedures, create drawings everyone in the shop can access, keep track of welding operator’s qualifications, and many other things. Software such as this can be tailored to the individual company’s needs and provide great efficiencies and also eliminate mistakes. Adding Robotics or Hard Automation to the Operation: Today’s technological advances offer many options. Robotics can be justified when the volume of parts a company produces is so great that it can offset the monies spent on a robot. Robotics can also be considered if there are a number of different parts that are similar enough in nature to be able to be handled by the same robot. If robots are not justified, a company might determine that fixturing or hard automation could be used to increase efficiency or quality. One company incorporated fixturing and clamps to hold down a tank while the seam was being welded. In another case, an automotive manufacturer decided that automation was necessary because of the amount of parts and intricate angles and welding positions.

These welding tables are manufactured to the highest standards in Poland, Europe by GPPH. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. The hole system that these welding benches offer make precise construction a much quicker process when used in conjunction with the optional tool sets. Batch work processing times can be cut in half when you eliminate the measure and exact angle arrangement of individual parts – this makes producing the same item simple and fast.

The Hobart Handler 210 has the typical great quality Hobart build with durable parts that stand the test of time. The 210 is more suited to autobody repair and construction than the 190 and 140 and it welds up to 3/8 inch. It’s also a flexible unit with the capacity to weld off 115V and 230V. At under $1000 it’s lot cheaper than the Ironman 230 and is a wise choice if you’re looking for a welder that packs real power but isn’t the price of the heavy industrial welders. It you’re looking for the all round MIG package for power, versatility, quality and value for money, the Hobart 210 is our top pick. See our full review of the Hobart Handler 210 here.

The people behind Display4top market this particular model as a professional MIG welder and we can’t say that they make a poor case in that regard. For one, its duty cycle is definitely up there. With its 48A rated output, the model is able to work for 6 minutes straight before overheating. It comes equipped with a variable wire speed control trigger, so you’ll be able to efficiently work with different metals. There are two power settings and an Ampere knob, further making the versatility case. More importantly, the model is as durable as they come. The forced air cooling system keeps the temperature at a nice, practical level. On top of that, the welder incorporates a thermal overload protection system that will be able to pick up the former’s slack in case it fails to do its job. Read more details on Mig welder.

If you’ve been searching for a small MIG welder which you can take with you to local jobs, then the Dirty Pro Tools professional welder could be an excellent option for you. Designed for the experienced welder, this high-quality device comes with a range of accessories to improve your welding experience, including a helmet, a welding wire brush, a clipping hammer, and an earth clamp. Created with durability in mind, the Dirty Pro Tools welder is ideal when you want something that will stand the test of time and deliver an excellent quality weld. During the welding process, the flux protects the system, and there are four power settings available, so you can choose the strategy that works best for you, complete with variable wire speed control. No gas is required for this machine or car welder, and it uses both filler wire or flux cored wire. To keep the welding machine working at optimal conditions and extend its duty cycle, there’s a turbo fan cooling the internal workings. For portability, you can even use the helpful handle on the top of the welding machine.

Awesome Oxygen Gas Cylinders store United Kingdom? Welding Supplies Direct stocks a huge range of Industrial gas. Cylinders of Industrial Gas can be delivered directly to your door from our Telford facility. Gas can also be collected from us should you require it. Our team are experts in helping you to find the right industrial gas for your needs. All we need from you is some information to help us to find the correct gas for you, simply tell us: What process are you undertaking. The type of material that you are welding. How may Industrial gas cylinders do you need. Were you are in Shropshire, Staffordshire and the Westmidlands.

The Everlast Powermig 200 welder offers dual voltage inputs and weighs only 35 pounds due to inverter technology. It’s not only MIG-capable, you can also use it for flux core welding or as a stick welder. When your machine can stick weld and connect gas at the same time, all you need to buy is a connector block and you gain TIG ability too, although Everlast doesn’t say so. The Powermig 200 features a burn back control, automatically adjusting the wire length at restart. 200 amps can weld ?-inch steel in a single pass. Dual digital displays and a low-spatter arc control system are nice features in this price range. Preflow and Postflow improves weld quality, reducing porosity by starting the gas shield before the arc begins and cutting the gas off after the arc stops. The burn back control feature resets the length of the wire feed before you strike another arc. Another nice feature is the digital controls that give you a nice reading of exactly what your voltage and wire speed is. Everlast includes a gas regulator with this rig and backs it with a 3-year warranty. With stick capability and the ability to use it on either household or industrial power, this is quite a bit of welder for the money. Looking on the internet for the highest quality Oxford MIG welder?

The following tips may help: Use the right type of regulator for the gas cylinder. Take care to inspect the regulator before attaching to the cylinder. If the connections aren’t properly made, perhaps you might be using the wrong device. Thus, it is wise to replace it with the right one. Close the valve of the cylinder, as well as release the pressure from the regulator, before removing it from a cylinder. Remove the regulator from the cylinder while transporting it to another location. Find extra info on https://www.weldingsuppliesdirect.co.uk/industrial-gas.html. Semiconductors are built and shaped using largely gas materials. In fact, gases have always been a key enabler of semiconductor fabrication, even though the types used continue to change and grow as manufacturing processes evolve. Gases have the ability to create chemical reactions at the molecular level, helping to shape a semiconductor’s electrical conducting properties to allow or prevent the movement of electrons. But, in order to ensure the semiconductor is configured to properly regulate electron movement, these gases must be precisely and accurately dispensed at every stage of its engineering process to incite the right reactions.

Delivery of parts to the welding station in an organized and logical fashion is also a way to reduce welding costs. For example, one company was manufacturing concrete mixing drums. In the fabrication process, the company produced 10 parts for one section, then went on to make 10 parts of another drum section, etc. As pieces came off the line, they were put onto the floor of the shop. When it was time to weld, the operator had to hunt for the pieces needed and sort through them. When the outside welding expert pointed out the amount of time being wasted in this process, the company started to batch each one on a cart. In this way, the pieces needed to weld one drum were stored together and could easily be moved to the welding area. This type of scenario is also true for companies that may outsource parts to a vendor. Though it may cost more to have parts delivered in batches, it may save more in time than having to organize and search through parts to be able to get to the welding stage. How many times each piece is handled in the shop may be an eye-opener to reducing wasted time. To measure such an intangible as this, operators are asked to put a soapstone mark on the piece each time it is touched – some companies are surprised to find out how many times a part is picked up, transported and laid down in the manufacturing process. In the case of one company, moving the welding shop closer to the heat treatment station eliminated four extra times that the part was handled. Basically, handling a part as few times as possible and creating a more efficient production line or work cell will reduce overall costs.

How to pick a welder tips: MIG wire inch button: A great feature. This will save you wasting your shielding gas when feeding wire through at the start of a new reel. Gas purge button: Another nice option. Save yourself some MIG wire, when you’re setting your gas flow. Burn back facility: Not all machines have this externally, buy it’s good to be able to trim the burn back to the wire according to the application & operator. Selecting the correct amperage machine: Generally, you should work on 35-40 amps per 1 mm diameter of material to be welded.

Several advices on welding equipment, MIG and TIG welders, plasma cutters. ARC Welding : ARC welding is one of the oldest welding processes around. It uses either an AC or DC power supply to create an electric arc between the welding rod and the workpiece metal to melt the metals and join them together. This style of welding is relatively inexpensive and very portable but it does require some practice to get good consistent welds and the welds will probably require some arc weldercleaning up afterwards. ARC welding is less suited to welding thinner materials but there is a large range of specialist electrodes (welding rods) available for ARC welders depending on what materials you are welding. ARC welding is versatile but more suited to heavier applications.

ESAB is a world leader in the production of welding and cutting equipment and consumables. Our innovative, world-renowned equipment and solutions are developed with input from our customers and built with the expertise and heritage of a global manufacturing leader. For each discipline, continuous development of methods, materials and know-how is being directed to meet the challenges posed by the diversity of industry sectors we serve. ESAB is organized to deliver efficient, high-productivity solutions to meet customer requirements in a manner that exceeds their expectations no matter the market segment. Continuous Improvement (Kaizen) Is Our Way Of Life – Set breakthrough objectives, experiment and learn every day, eliminate waste in our business processes, and benchmark the best, then better them. Living this value is done through understating that Change is a Must, and the use of Tools for Improvement. To live this value each ESAB associate fosters an environment of continuous learning employing the Colfax Business System Tools which is the basis of our culture.

GPPH’s tables offer an incredibly stable and sturdy construction. The table top is made from 15MM thick material, this is outstanding when compared to the typical 6MM – 10MM that is usually used on lower end welding tables. In addition to this, the steel used is S355J2+N grade that is carefully selected. The steel is also unpickled so as to prevent the material becoming bright and causing arc to flash bounce off the table making the working conditions difficult for the welder. Finally, the tables are not coated with paint as it can make the surface difficult to conduct. They are coated with an oil based preparation which protects the tables during transport. Anti spatter is suggested.

The Lincoln EasyMIG 180 is a well-built welder that’s reliable and will serve a range of light fabrication and workshop projects. Its power input is 230V but it doesn’t have the power of the Hobart 190. This is a great entry level 230V welder that will give you quality welds. It won’t tackle thicker metal but this will do the job for most hobby welders. It’s a great choice for a hobbyist if you have a convenient 230V power outlet.

Gasless welding, which is also called “Gasless” or “No-Gas” welding, is the main convenience of contemporary MIG welders. That means they can make welds either with or without gas. It is possible thanks to the use of a special tubular wire filled with a flux and metal powder called a flux-cored wire. In a nutshell, when a flux-cored wire is used, its components generate a shielding gas under a high temperature that is essential for a high-quality joint. The thermal overload protection is also a useful feature that will switch the unit off automatically if the temperature reaches a certain level. Surely, a MIG welder is not something you will carry every minute. Yet, if a machine is lightweight and fitted with wheels, using it will be much more pleasurable. Finally, pay attention to the kit each tool comes with. Some models include a welding shield, coil, attachment for flux-cored welding, hammer, or brush. So, take these features into account when buying a welder.

United Kingdom market pick: Hobart is an American welding company that has produced quality machines since its inception in 1917. Often toted as the best MIG welder for beginners, the Handler 140 is an affordable and easy to use machine right off the bat. Though its duty cycle is on the low end when compared to the other welders on this list, the Handler is a crowd favorite. It is also fairly easy to carry. Welders will love the portability and ease of use. A home hobbyist will get years of use and enjoyment from this powerful machine. All in all, it’s a very sturdy machine and is manufactured in the USA. See more details at here.

Finally, if you’re looking for a home welder, then you don’t necessarily need the most powerful machine on the market. Some people invest in MIG welders specifically to support their home-based projects, when they’re creating something new in the garage, or working on adaptions to pieces of machinery and furniture. The Clarke MIG151EN is designed for the DIYers who can’t afford to compromise on quality. Complete with professional specifications like a non-live torch and an extra-tough protective coating on the front and rear, the Clarke turbo MIG welding machine comes with everything you need to start welding at home. There’s a thermal overload protection system to give you complete peace of mind, as well as a very powerful wire drive motor included. Additionally, you’ll be pleased to know that all Clarke products comply with the highest quality of European and safety standards. As a winner of multiple third-party awards, Clarke offers a high-performance option for anyone searching for an arc welder for home use. The rotary power selection system also means that you can choose the level of performance you need with ease.

Top fume extractors online store UK 2021: This portable weld fume extractor weighs 50 pounds only and features a 16-foot flexible wire. I’ve found the wheels to be extremely useful to move it around anywhere I need. It’s perfect for people who want something efficient but highly portable as well. The S130/G130 is an excellent option for manual welding around the house and store. Adaptable and Durable. The S130/G130 is a highly adaptable and powerful welding fumes extraction system in a small size. This unit can be used at welding school training due to its compact build quality and efficient fume extraction system. The 16-inch hose that it comes with is enough to cover any small to medium area. The machine is made with high-quality steel that makes it sturdy and durable. See more info on https://www.weldingsuppliesdirect.co.uk/welding-equipment/welding-fume-extraction.html. The Aoyue AO486 486 Benchtop Solder Smoke Absorber is the perfect fume extractor for arts and crafts projects, electronics, or stained glass work. It is very quiet when doing its job. Furthermore, it has a powerful operator that will make every cent worth it. Similar to most systems, the Aoyue AO486 486 also features an activated carbon filter. On top of that, this product has been tested by ESD. Aoyue SRA Soldering Products started way back in 1962. They have been manufacturing, distributing, and importing various products including fume extractors. Some of its key features include a stand with an adjustable pivot, a replaceable carbon filter, AC powered, and a fairly quiet operation.

A few tips on welding equipment, MIG and TIG welders, plasma cutters. Identify the types of welding projects and materials you will weld most of the time. Are you creating metal sculptures? Do you intend to restore an old muscle car in your garage? Does the motorcycle you bought years ago require some fabrication? Maybe you need to do basic repair on farm equipment. Taking the time up front to identify the projects that will occupy the biggest percentage of your welding activity will help you determine the specific thickness of metal you will likely weld most often – and ultimately help you select the most suitable welder. Time to get a bit more specific. Let’s take a look at what welding process you can use for each metal type. Keep in mind that many of these materials are also processed using varying combinations of two or more metals to reinforce strength and functionality.

When working on DIY projects in your workshop, it can be easy to forget how much damage certain fumes can cause to your health. With the best fume extractor installed, this is no longer an issue. Read on to learn how to get your hands on a great fume extractor to install in your workshop. The Kulannder Handy Carry Solder Smoker is a portable smoke extractor/fume extractor built on sturdy aluminum alloy material, is ideal for using electronic workshops, and also an excellent fit for arts, craft and stained glass work stations. It offers a maximum airflow of 2000ml/min, which make it the best fume extractor of its class and can run a lifetime, approximately 50,000 hours.

Top quality MIG welding machines plus MIG welders online store: Before you get started, conduct online research to see what the best practices are for the specific wire you have or contact a trusted filler metal manufacturer. Doing so not only tells you what the manufacturer’s recommended parameters are for your diameter wire, but also what the proper wire feed speed, amperage and voltage is, along with the most compatible shielding gas. The manufacturer will even tell you what electrode extension or contact-to-work distance (CTWD) is best suited for the particular wire. Keep in mind that if you get too long of a stickout, your weld will be cold, which will drop your amperage and with it the joint penetration. As a general rule of thumb, since less wire stickout typically results in a more stable arc and better low-voltage penetration, the best wire stickout length is generally the shortest one allowable for the application. Explore more info on https://www.weldingsuppliesdirect.co.uk/.

High quality online provider to purchase gas bump in UK: In answer to your questions, there are a number of choices available for gases and gas mixtures that can be used to weld aluminum. The choice is usually based on the specific application. Generally speaking, the high helium content gases are used for GMAW welding on thicker materials and GTAW welding with DCEN. Pure argon can be used for both GMAW and GTAW welding and is the most popular of the shielding gases used for aluminum. The helium content gases are usually more expensive. Helium has a lower density than argon and higher flow rates are used when welding with helium. It is possible to increase welding speeds in some circumstances by using helium and/or helium/argon mixtures. Therefore, the extra cost of the helium mixtures may be offset by your improved productivity. You should try the different gas types and choose the one that best suites your specific application.

Premium industrial PVC curtains online shopping in 2021? Here at PVC Strip, we are not immune to what happens on the global stage and to these rising costs. We have worked hard and continue to do so to minimise the impact of these price increases to our customers as much as we possibly can. This includes focussing on our price promise guarantee and extending this throughout 2021, absorbing as much of the external cost increases as we can to remain the best value supplier of industrial PVC Curtains and associated products.

Our mesh lightweight, mesh strips available in black or grey come as standard with weighted bottoms to ensure they don’t flap around in the wind. These are stylish mesh covers are designed to aid open kitchens and food production environments that desperately need fresh air circulating. The mesh strips allow hands-free access through doorways and remove the hassle of health and safety concerns that come with flies, insects and bugs buzzing around and contaminating food produce.

What about when the strip curtains become dirty? Not to worry, they are easy to clean. All you really need is a bucket of clean warm water and a nice big sponge. Just simply wiping and rinsing with warm water will be enough to get most of the dirt off. If not, a solution of specialist PVC cleaning fluid will get the last bits of grime and grease off. Once you have cleaned the strips, dry down to avoid streaks just like you would when cleaning a window. If your PVC strips are incredibly old, slightly damaged, or beyond simple cleaning, you can purchase individual replacement strips to match the ones on your curtains. Discover more info at PVC strip curtains.

PVC-Strip are the UK’s largest manufacturer of PVC strip curtains and hold the largest stock of PVC strip rolls in the UK. We offer a price match guarantee on our PVC strip curtains and will not be beaten on any “like for like” written quotation. We constantly review our pricing so we can remain extremely competitive in the PVC market. Please contact our sales team to discuss your PVC strip curtain requirements and in the unlikely event we are ever out on price we will review our competitors offer and beat it. We can guarantee that when you purchase from PVC-Strip, you are purchasing the highest quality product at the best price on the market.

PVC Strip is a specialist in manufacturing high-quality industrial PVC strips in the UK and is the largest supplier and stockist of PVC strip curtains, PVC rolls, PVC sheets, and associated suspension systems for PVC curtains. We actively supply our PVC products into numerous market sectors including: food and cold-storage, cleanrooms, datacentres, schools, construction, cold chain logistics, warehousing and storage, agriculture and hospitality. Discover additional info on https://www.pvc-strip.co.uk/.

Premium Propane cylinders store UK 2021? Always use a cylinder trolley or fork lift truck to move cylinders.: When moving individual cylinders always use a cylinder trolley and for MCPs (Manifold Cylinder Pallets) ensure they are transported by a fork lift truck driven by a qualified operative. Don’t forget to make sure all cylinders are secured and the valves are closed before moving them. You should always know what you are handling: Always use the cylinder label to identify the contents of the cylinder, rather than relying on the colour of the cylinder. If a label is missing or unreadable, don’t use the cylinder.

The Hobart Handler 140 is a bit of a hybrid between pro-level performance and homeowner convenience. The 140-amp rating is enough to weld up to 1/4-inch steel. This machine works both as a flux core welder and as a MIG. The duty cycle is 20 percent at 90 amps. That’s enough power to do most jobs you’ll ever tackle in a home shop setting, but for professionals working on heavy stuff like trailer frames or pipe fencing, it’s just not going to be enough. For other professional work like auto body or welding brackets, mountings and the like, this machine can run off a 4000-watt generator. It’s small enough to carry into a home for HVAC repair and the 110/115/120 input means you could use a small generator or the household receptacle to do the work. The solid aluminum wire drive accommodates either 4 or 8-inch spools and it’s selectable between multiple gauges of wire. The Hobart Handler 140 is backed by a 3-year warranty and its professional features and true MIG capability make it the our Pro Value Pick in this review roundup. Searching the internet for the highest quality MIG welder?

Use the Personal Protective Equipment (PPE): It is mandatory to use various appropriate PPE while handling an industrial gas cylinder. For instance, wear safety glasses, safety shoes, gas masks, and safety glasses, while working with cylinders filled with compressed gases. Similarly, it is important to use flame arrestors when using acetylene cylinders in compressed air. Use Regulators Properly While Handling Cylinders: Regulators are devices, which are designed to lower the working pressure of the gas. These devices differ according to gases. Many times, the regulators aren’t handled and stored properly. This improper usage may lead to problems in the long run. Hence, it is important to take several precautions while using regulators. Read more details on https://www.weldingsuppliesdirect.co.uk/industrial-gas.html. In addition, argon is used in conjunction with oxygen in a common technology for refining stainless steel. Industrial gases also have important applications in metal fabrication. For instance, acetylene is used for welding and metal cutting and argon is used as a shielding gas for the electric arc welding of nonferrous and specialty metals. Nitrogen is used in heat-treating and metalworking for products such as metal sheeting, rods, wires, and castings.

Delivery of parts to the welding station in an organized and logical fashion is also a way to reduce welding costs. For example, one company was manufacturing concrete mixing drums. In the fabrication process, the company produced 10 parts for one section, then went on to make 10 parts of another drum section, etc. As pieces came off the line, they were put onto the floor of the shop. When it was time to weld, the operator had to hunt for the pieces needed and sort through them. When the outside welding expert pointed out the amount of time being wasted in this process, the company started to batch each one on a cart. In this way, the pieces needed to weld one drum were stored together and could easily be moved to the welding area. This type of scenario is also true for companies that may outsource parts to a vendor. Though it may cost more to have parts delivered in batches, it may save more in time than having to organize and search through parts to be able to get to the welding stage. How many times each piece is handled in the shop may be an eye-opener to reducing wasted time. To measure such an intangible as this, operators are asked to put a soapstone mark on the piece each time it is touched – some companies are surprised to find out how many times a part is picked up, transported and laid down in the manufacturing process. In the case of one company, moving the welding shop closer to the heat treatment station eliminated four extra times that the part was handled. Basically, handling a part as few times as possible and creating a more efficient production line or work cell will reduce overall costs.

How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).

Several tips about welding equipment, MIG and TIG welders, plasma cutters. TIG Welding / Gas Tungsten Arc Welding (GTAW) — TIG welding is an arc welding process that uses a non-consumable tungsten electrode to produce the weld. The weld area is protected from atmospheric contamination by a shielding gas (usually argon) and a filler metal, though some welds, known as autogenous welds, do not require it. A constant-current welding power supply produces energy that is conducted across the arc through a column of highly ionized gas and metal vapors known as plasma. TIG welding is most commonly used to weld thin sections of alloy steel, stainless steel and nonferrous metals such as aluminum, magnesium and copper alloys. The process grants the operator greater control over the weld than other welding processes, allowing for strong, high-quality welds. TIG welding is comparatively more complex and difficult to master than other processes and is significantly slower.

Our vision and our distinct set of values drive the success and spirit of our organization. At ESAB, under Colfax leadership, we live our values. As a premiere U.S. welding equipment manufacturer, our vision and values help us to make strategic decisions, allocate resources, and focus our choices every day, domestically and internationally. ESAB offers a world of products and solutions for virtually every welding and cutting process and application. We serve industries that serve the world. The Best Team Wins – Team-oriented, involved associates are our most valuable resource, and we are passionate about attracting, developing, and retaining the best talent. Living this value is done in three primary ways: 1. Building the right team – having the right people to do the job; 2. Creating the right environment – making sure that leaders create an environment where all associates can contribute, and 3. Getting the win – when you have the right people and right environment – it makes getting the win a lot easier!

These welding tables are manufactured to the highest standards in Poland, Europe by GPPH. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. The hole system that these welding benches offer make precise construction a much quicker process when used in conjunction with the optional tool sets. Batch work processing times can be cut in half when you eliminate the measure and exact angle arrangement of individual parts – this makes producing the same item simple and fast.

The Hobart Handler 140 is an excellent choice for beginner welders, which is why it’s probably the most popular welder on the market. This thing is solidly built and is a step above many of the other 140A welders. The arc runs smooth and produces great results. It’s suitable for a range of general repair tasks and projects like trailer frames, autobody repair and anything up to 1/4 inch thick. If you’re just getting into welding, you can’t go wrong with this little machine! What’s better is that it’s an absolute steal at under $500. See the full review here.

The people behind Display4top market this particular model as a professional MIG welder and we can’t say that they make a poor case in that regard. For one, its duty cycle is definitely up there. With its 48A rated output, the model is able to work for 6 minutes straight before overheating. It comes equipped with a variable wire speed control trigger, so you’ll be able to efficiently work with different metals. There are two power settings and an Ampere knob, further making the versatility case. More importantly, the model is as durable as they come. The forced air cooling system keeps the temperature at a nice, practical level. On top of that, the welder incorporates a thermal overload protection system that will be able to pick up the former’s slack in case it fails to do its job.

United Kingdom market pick: LOTOS Technology is a California company that has only been around since 2007. Still, the LOTOS MIG is impactful and high quality enough to make it onto our list. This one is a versatile machine that is a fair price of about $400. And—provided that you have the necessary 240-volt outlet in your home—it can be set up in a matter of minutes. The duty cycle of this welding newcomer is impressive, and it can be utilized by pros and amateurs who have been continually impressed by the bang they’ve gotten for their buck. The LOTOS can weld steel and stainless steel from 18 gauge to ¼ inches and aluminum to 1/8 inch or thicker. Thermal overload protection doesn’t let this machine overheat, and infinitely adjustable heat/amperage as well as wire speed makes using the LOTOS simple. Check out the LOTOS MIG140 for a lower power alternative. Discover extra info on here.

It’s also worth looking into how your welder will handle things like short-circuiting. If a short circuit issue occurs while you’re welding, you don’t want a surge of power to ruin your work. Fortunately, there are many welding companies that implement strategies in their devices to eliminate the risks of short circuits. To choose the correct portability, size and weight for your welder, you’ll need to think about what you’ll need the machine for. If you’re going to be carrying it around a lot, then you need something that’s going to be highly portable and lightweight. Just make sure that a reduction in weight doesn’t mean that you end up compromising on power or performance.

Eds analysis services in Chelmsford, MA right now? Analysis and Results: The submitted bottle was examined for signs of interior distress, and the water from the bottle was removed and maintained. Some of the suspended particulate was filtered and examined non-destructively by light microscopy first, to characterize the material. A low magnification stereo microscope image of the filtered white particulate is shown in the image above. From this image, biological tissues were ruled out, and the material was observed to be crystalline. Polarized light microscopy (PLM) was used to analyze the sample next. From this examination, the material showed birefringence as shown in the PLM image on the right. The PLM Image Stereo Microscope image suspect material showed optical properties and morphology dissimilar to common carbonates and sulfates. It was determined to be a birefringent crystalline material, but it could not be identified using only PLM methods. Therefore, analysis using scanning electron microscopy with energy dispersive x-ray spectroscopy (SEM-EDS) would have to be performed to obtain further information about the suspect material.

SEM is a powerful surface microscopy method which allows for high resolution images to be obtained on a wide range of samples. A focused beam of electrons sweeps across a sample surface and an image is created from the scattered electrons. The electron beam allows for the accurate imaging of features below the resolution limit of visible light. The acquired pictures retain good depth of field, resulting in excellent three-dimensional images. Variations in beam parameters can be made in order to highlight variations in density in the target sample, show extremely fine surface features, and illustrate texture in sample surface coatings. MicroVision Labs has multiple fully-operational SEMs, Bruker X-Flash EDS detectors and mapping technology, backscatter electron (BSE) imaging, and large chamber capabilities. These provide a full suite of microscopy services for all of your analytical needs.

What if I want a service not listed in your services list? At MicroVision Labs the list of services which we provide to our clients is constantly growing. So if you don’t see what you are looking for give us a call or use the Contact Us tab. Also don’t forget to check our Additional Services Page to see if it might be listed there. Can you identify a contamination or unknown for us? Yes, we call that an Unknown Material ID and we routinely work on that kind of project. We have a number of individual tests designed to classify unknown materials. When combined with our extensive suite of equipment, these tests allow us to identify virtually any material. Give us a call and talk to one of our knowledgeable staff for more information. Find a few more details at more info. ?MicroVision Labs is owned and operated by a career microscopist, John Knowles, who understands the needs of our clients. Our emphasis on helping our clients solve problems, not just providing data, sets us apart from other labs. We have the technology and knowledge to find answers to your most difficult challenges, helping you succeed at every step. Can I come in to see my samples analyzed? Yes, our clients are always welcome to come in while their samples are being analyzed. For much of the work we do, it is mutually beneficial for our clients to be present to help direct their project since they can provide expertise about their samples. Some of the services we provide such as polished cross sections have time consuming steps making it impractical for a client to stay to watch everything. In those cases it is recommended that you come in initially to explain what you need done and come back at a later time to see the finished product.

Also, the color EDS map highlights the iron particles in the mineral filled PVC floor. These iron particles were concentrated in areas were the tile showed signs of impact which indicated some metallic object impacted the tile leaving behind small particles and over time the materials oxidized which created darker spots in the tile. The data indicated that a significant portion of the dust was from the insulation in the attic. The contractor had replaced a portion of duct work running to the master bedroom. During this replacement, fiberglass insulation was knocked into the ducting. The small glass insulation fibers were spread through the AC ducts and settling out of the air throughout the house. The client was relieved to know what was causing their skin irritation and the significant dust build up. Using the results garnered from the analysis from MicroVision Labs they were able to have the contractor clean out the duct work and act to prevent further spread of the insulation fibers and properly clean up the settled dust in the house that was the cause of the homeowner’s skin irritation.

The client was contacted with the results, and was curious as to what the source of these particles might be. After consulting with the office manager, it was determined that some pieces of furniture present had relatively significant amounts of direct water exposure, and were subsequently dried a number of times during remittance construction. Inspection of these pieces of furniture showed that they had high density, close packed foam cushions of a type similar to the particles observed in the surrounding area, which had been broken down by the repeated wet/dry cycle. Explore extra info on https://microvisionlabs.com/.

Eds analysis providers in the USA today? Conclusion: Based on the analytical report, the client was able to demonstrate that the particles were consistent with a common aspirin tablet. When the end customer was approached with this report, they remembered that their spouse had taken an aspirin earlier that morning, and had likely used the bottle of water in question to do so. Based on this, the customer was happy, the manufacturing client was satisfied, and the sample was maintained – undestroyed should someone need to examine the sample again or do any more esoteric testing. For an affordable price, the client was able to get piece of mind, and gather information from a very wide range of testing methods quickly and accurately.

SEM allows for high magnification surface examinations of a wide variety of samples. Providing brilliant resolution as well as incredible depth of field, the SEM, especially when combined with EDS, is often considered the most powerful analytical tool of our time. Let us show you why. X-ray imaging allows us to look inside of a device without opening it up. This real-time nondestructive inspection technique can be used on packaged electronic devices to one of a kind ancient artifacts. With rapid image acquisition and high sample throughput, X-ray imaging is particularly useful for sample screening and quality control issues. It is also often the first step in failure analysis and polished cross section projects.

What if I want a service not listed in your services list? At MicroVision Labs the list of services which we provide to our clients is constantly growing. So if you don’t see what you are looking for give us a call or use the Contact Us tab. Also don’t forget to check our Additional Services Page to see if it might be listed there. Can you identify a contamination or unknown for us? Yes, we call that an Unknown Material ID and we routinely work on that kind of project. We have a number of individual tests designed to classify unknown materials. When combined with our extensive suite of equipment, these tests allow us to identify virtually any material. Give us a call and talk to one of our knowledgeable staff for more information. Find extra info on see it here. ?MicroVision Labs is owned and operated by a career microscopist, John Knowles, who understands the needs of our clients. Our emphasis on helping our clients solve problems, not just providing data, sets us apart from other labs. We have the technology and knowledge to find answers to your most difficult challenges, helping you succeed at every step. Can I come in to see my samples analyzed? Yes, our clients are always welcome to come in while their samples are being analyzed. For much of the work we do, it is mutually beneficial for our clients to be present to help direct their project since they can provide expertise about their samples. Some of the services we provide such as polished cross sections have time consuming steps making it impractical for a client to stay to watch everything. In those cases it is recommended that you come in initially to explain what you need done and come back at a later time to see the finished product.

A client responsible for maintaining the facilities in a public school district called with concerns of a possible mold problem. Areas with high foot traffic, especially those where students tracked water in, were showing dark black spots in the floor tiles. Aggressive cleaning and buffing of the floor would remove the problem for a while, but after several few weeks, the problem resurfaced. The facilities management staff was convinced it was mold related, but sending samples, swabs, and air grabs to a mold lab for culturing showed no sign of fungal structures on the tiles.

The client was able to obtain a comprehensive sampling of the state of the soldering process from the new manufacturer at a very reasonable cost. Rather than acquiring a mass of images, electrical test print outs, or low resolution optical pictures, the client received a comprehensive report detailing the relevant findings of the analysis on the boards from the new manufacturer. The solder joints in this study showed good bond integrity as well as excellent intermetallic layers. These findings allowed for the validation of the new manufacturer and their process which allowed for the clients device production to resume. The QC Engineers were very pleased with the customer service, analysis, pricing and quick turnaround time of this project. Discover a few extra details at microvisionlabs.com.